Range of spherical valves with brass or DZR brass bodies, chromium plated brass or chromium plated DZR brass (12-18mm) or stainless-steel balls (22-54mm) and various operating members The press-fit connection is for use with copper pipes (manufactured to EN 1057), stainless steel pipes (manufactured to EN10312) or carbon steel pipes (manufactured to EN10305-3). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of inline, angled or tee type spherical valves with brass (CP5R models), nickel plated brass (CP12 and CP02 models) or chromium plated brass (CP13 models) bodies, brass (10.20105.22X.CP5R-8510 and 10.20105.28X.CP5R-8510 models) or chromium plated brass (all other models) balls. The valves are either screwdriver, lever or butterfly handle operated (see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (10.60145.015.CP12-8510 and 10.61055.022.CP12-8510 models) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of screwdriver operated spherical valves incorporating brass bodies and chrome plated brass ball. The compression and press-fit connections are for use with copper pipe (manufactured to EN1057). Jointing of the press-fit connection is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of in-line hex key operated spherical valves incorporating nickel plated or chromium plated brass bodies and chromium plated brass balls. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with stainless steel bodies, stainless steel ball and lever operating members. The press-fit connection is for use with stainless steel pipe (manufactured to EN10312). Jointing is achieved via a crimping tool using a ‘M’ profile. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and wedges. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Flomasta Range of plastic, push-fit stop valves for use with MDPE pipe (manufactured to BS EN 12201). Maximum working pressure 16.0 bar. Cold water use only.
Magnetic and electrolytic scale inhibitors incorporating nickel plated copper bodies. For use with copper pipe manufactured to BS EN 1057. Maximum working pressure 10.0 bar. Cold water use only.
Water filter and scale inhibitor comprising of a plastic filter head and plastic filter cartridge with an activated carbon block and sodium polyphosphate. The push-fit connections are for use with LDPE pipe (manufactured to DIN 8072). Maximum working pressure 5.52 bar. Cold water use only.
UV Home’ range of UV disinfection units with 304L or 316L stainless steel bodies (see models). Maximum working pressure for UV HOME 2 & 3 is 6 bar. Maximum working pressure for UV HOME 6 & 9 is 10 bar. Maximum operating temperature 35°C.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 451B'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS 'CR451B/CP573X', dated 'Sep 24, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M-AC010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user manual 'rev. 2.0R' dated 10/10/2024. Cure for 20 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GRP-FPI Qatar Fiberstrong GRP Pipe'. Multi-layered GRP pipe comprising of a green coloured inner layer, white coloured middle layer and green coloured outer layer, manufactured by filament winding. Between April 2024 and November 2025, the pipe is for use with water up to 23°C. Between December 2025 and April 2030, the pipe is for use with water up to 50°C.
'SINTA-GRP-01 Water Tank Panel'. Natural (appears off-white), hot press moulded GRP panel. For use with water up to 23°C.
Page 460 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
