'Plascoat PPA571 Aqua Blue 536'. Factory applied, blue coloured PE coating. Apply by flock spray coating and fluidised bed dipping (and post-cure as necessary) in accordance with TDS dated 23/02/2015. Please refer to ‘guide to typical coating conditions – batch operation'. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPICOAT 1000'. Factory applied, two-component, red coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/006', 'version 01', dated '03.11.2022'.. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DICOAT 60EX'. Factory applied, two-component, blue coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/007', 'version 01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOGUARD APC 301'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's Technical Data Sheet, 'rev.01', dated April 2022. Cure for 7 days@28°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ECO-Coat FBE Black Powder PFC/5010'. Factory applied, black coloured epoxy coating. Apply as per manufacturer's IFU 'Doc/PFC/710', revision 1, for 3 minutes at a metal temperature of @220°C. For use with water up to 85°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROTECSOB BEC3'. Factory applied, mustard coloured (once mixed), two-component epoxy coating. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's TDS reference '28712'. Cure for 15 hours@70°C. For use with water up to 70°C. From December 2023 the coating is for use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘FLOGUL® 656 Bleu 5005’. Factory applied, blue coloured VOC paint. Apply as per manufacturer’s TDS dated ‘06/04/2022’. Cure for 7 days@20°C. For use with water up to 60°C.
‘R-4401, E-44131, E-4413, E-4414, E-4420, E440001, E441001, E440002, E441002, E-5402, E-5403, E-5404, E540001. E541001, E540002, E540003, E541003 & E440007’. Factory applied, grey-blue coloured enamel coatings. Apply as per manufacturer’s instructions ‘issue 02/2016’ dated 05.10.2016. Cure for 6 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DiChem Tiestop'. Site applied, grey coloured cementitious repair mortar. Mix 'DiChem Tiestop' and water in a mass ratio of 9.4:1 and apply as per manufacturer's instructions 'Rev 4, 02.22'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 440 of 1134
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
