'LOCTITE® 5400™’. Yellow coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.3’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Weld-On 705 ECO Clear PVC cement'. Clear solvent cement. Apply as per manufacturers technical data sheet '705 ECO-09-2024'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ULTEM™ PW1010-1000'. Amber coloured, injection moulded PEI (polyetherimide) material. For use with water up to 85°C.
Bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum operating pressure 10 bar. Maximum operating temperature 40°C.
Material included on initial approval: 'XRRA 410B GR1500'. Material added to approval in December 2025: ‘RRA 406B GR1500’. Grey coloured, injection moulded U-PVC materials. For use with water up to 23°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Concealed WC dual flushing cisterns with a BS 1212- 4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a manually operated dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The inlet supply incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Five-hole, single outlet (fixed) combination tap assembly with brass bodies (various finishes), incorporating a quarter turn ceramic disc headworks to control the flow and a manual diverter to shower outlet both with single lever operating members. The spout outlet incorporates an aerator. The product is supplied with a pull out shower hose and shower handset, metal backnuts and stainless steel braided, EPDM lined interconnecting hoses. The handset also incorporates an approved single check valve, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of ceiling and wall mounted shower arms with brass bodies (various finishes). Open outlet use only. Maximum operating temperature 85°C.
Range of CA-b backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of CAb backflow prevention devices with plastic bodies, incorporating EPDM seals and diaphragm. Filling link with manual or automatic tap. Maximum working pressure 3.0 bar. Maximum operating temperature 65°C.
Range of non-verifiable double check valve assemblies, consisting of two spring loaded resilient trim in-line check valve cartridges housed in DZR brass bodies, models AI-903215, Al-903222 & AI-903228 are chrome plated. Maximum working pressures: AI-903215, AI-903222 & AI-903020 16 bar. AI-903032, AI-903040 & AI-903050 10 bar. Maximum operating temperature 60°C Added September 2025 Maximum working pressure 10 Bar (AI-903025) Maximum working pressure 16 Bar (AI-903228) Maximum operating temperature 85°C
Range of push to open, push to close ‘detent’ headworks with plastic bodies, NBR ‘O’-rings and stainless-steel strainer. For insertion into specifically dimensioned bores. Maximum working pressure 10 Bar Maximum operating temperature 85°C
Range of ceramic cartridge headworks with plastic bodies, EPDM gaskets and NBR O-rings. The products are for insertion into specifically dimensioned bores. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of non-rising spindle headworks with brass bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks with brass bodies. The 12333004-001 model is a 2-way ceramic disc diverter headworks. The 12333006-001 model is ¼ turn. For insertion into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) pull down spray combination tap assemblies (brass bodies – various finishes), model (62861-01X) incorporates quarter turn ceramic disc headworks, models (62931-00X & 62932-00X) incorporate ceramic cartridge headworks, all with single lever operating members. The outlet incorporates a plastic aerator. Model (62861-01X) incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Page 438 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
