Range of heat interface units (HIU) with either twin or single stainless steel copper brazed plate heat exchangers (depending on model) providing heating and hot water (twin unit) hot water only, or heating only. The hot water is generated via a plate heat exchanger. The primary (space heating) circuit incorporates an expansion vessel and a pressure relief valve (set at 3.0 bar). The product incorporates a CAb backflow prevention device (suitable for backflow protection against Fluid Category 3) for filling the heating circuit. The inlet and outlet of all circuits incorporate a lever operated spherical valve. Maximum working pressures and operating temperatures: Primary (district heating): 10.0 bar and 85˚C. Domestic hot water (DHW): 10.0 bar and 60˚C. Secondary (space heating): 2.5 bar and 80˚C.

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

2011358

Size:

22mm solder fitting

Marking:

Albion water management, model and other tech info on data label on the side panel.

Installation Requirements:

R001 R140

Expiry date:

30/11/2025

Model:

[Twin Unit]: Standard Twin Plate – heating with 24 plates and hot water with either 14 or 40 plates. Heating connection to cold water by filling loop. Products: TH000240 MTA TWIN 24-40 TH000214 MTA TWIN 24-14 TH001240 MTA TWIN 24-40 HM TH001214 MTA TWIN 24-14 HM [Hot Water Only]: Hot water with either 14 or 40 plates, connection direct to cold water. Products: TH000414 MTA HOT WATER ONLY 00-14 TH000440 MTA HOT WATER ONLY 00-40 TH001414 MTA HOT WATER ONLY 00-14 HM TH001440 MTA HOT WATER ONLY 00-40 HM [Heating Only]: Heating with 40 plates on domestic heating circuit only, connection to cold water via filling loop. Products: TH000340 MTA HEATING ONLY 40-00 TH001340 MTA HEATING ONLY 40-00 HM ‘HM’ stands for heat meter which is on the heating circuit

Product Images

Approval Holder:

Albion Water Management

Company Name

Albion Water Management

Address

30-31 Station Close, Potters Bar, Hertfordshire

Postcode

EN6 1TL

Phone

01707 607230

General Email

water@albiongroup.co.uk

View All Listings by this Company

Manufacturer:

Albion Water Management

Company Name

Albion Water Management

Address

30-31 Station Close, Potters Bar, Hertfordshire

Postcode

EN6 1TL

Phone

01707 607230

General Email

water@albiongroup.co.uk

View All Listings by this Company

Immersion temperature sensors with DZR bodies and an EPDM ‘O’-ring (STDW14 model only). Maximum working pressure 15.0 bar. Maximum operating temperature 100°C.

Section:

1530 Miscellaneous Fittings

Size:

STDW1410K00*** & STDW1410K01***: Ø 11.43mm. STDW1310K00*** & STDW1310K01***: Ø 9.66mm.

Marking:

ENPI, model and production code (YWW - see model for description) on body.

Installation Requirements:

R001

Expiry date:

31/07/2025

Model:

STDW1410K00*** & STDW1410K01***. STDW1310K00*** & STDW1310K01***. Where: 10K = resistance value at 25°C, (not verified or considered part of the approval listing). 00 or 01 = code number of NTC β value. *** denotes production year and week in the following format. 1st * = year, and is replaced with L = 2020, M = 2021, N = 2022, O = 2023, P = 2024, Q = 2025. 2nd & 3rd * = week, e.g. 15 = week 15.

Approval Holder:

ENPI Elektronic San, VE DIS TIC. AS

Company Name

ENPI Elektronic San, VE DIS TIC. AS

Address

Dudullu O.S.B. 1 Cad No 1 Ismet Tarman Is Merkezi

Country

K:1 D:13

View All Listings by this Company

Manufacturer:

ENPI Elektronic San, VE DIS TIC. AS

Company Name

ENPI Elektronic San, VE DIS TIC. AS

Address

Dudullu O.S.B. 1 Cad No 1 Ismet Tarman Is Merkezi

Country

K:1 D:13

View All Listings by this Company

Range of pump docking manifolds with plastic bodies and NBR, EPDM and FKM ‘O’-rings. Maximum working pressure 8.0 bar. Cold water use only.

Section:

1530 Miscellaneous Fittings

Size:

See model

Marking:

DAB water technology on plate attached to body.

Installation Requirements:

R001

Expiry date:

31/10/2025

Model:

60147247 E.SYDOCK - GAS: 1¼” BSP (F). 60150514 E.SYDOCK - NPT: 1¼” NPT (F). 60160491 E.SYTWIN - GAS: 1¼” BSP (F). 60162081 E.SYTWIN - NPT: 1¼” NPT (F).

Product Images

Approval Holder:

DAB PUMPS SPA

Company Name

DAB PUMPS SPA

Address

Via Marco Polo 14 Mestrino (PD)

Postcode

35035

Country

Italy

General Email

certifications@dwtgroup.com

View All Listings by this Company

Range of concealed bathroom boxes with extractable shower hoses. The inlet attached to the concealed box incorporates an approved single check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The outlet of the shower hose also includes a stainless steel strainer. Maximum operating temperature 60°C.

Section:

1530 Miscellaneous Fittings

WRAS Approval Number:

2007359

Note:

Open outlet use only. Water collection box discharge to drain must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717. This approval does not include a shower handset. R007 applies to the hose installed prior to the shower hose (all models). R009 applies to the INCISCO 01813 model.

Size:

½” BSP (M)

Marking:

Gessi on outlet for shower hose.

Installation Requirements:

R001 R007 R009 R040

Expiry date:

31/07/2025

Model:

INCISO 01813 (lower side supply). INCISO 01814 (lateral side supply).

Product Images

Approval Holder:

Gessi S.p.A.

Company Name

Gessi S.p.A.

Address

Parco Gessi Hamlet Vintebbio Serravalle Sesia

Postcode

13037

Country

Italy

Phone

+39 0163 454111

General Email

pfornara@gessi.it

View All Listings by this Company

Manufacturer:

Gessi S.p.A.

Company Name

Gessi S.p.A.

Address

Parco Gessi Hamlet Vintebbio Serravalle Sesia

Postcode

13037

Country

Italy

Phone

+39 0163 454111

General Email

pfornara@gessi.it

View All Listings by this Company

Range of submersible pumps incorporating stainless-steel bodies and plastic impellers. Maximum working pressure 23.0 bar or 36.0 bar (please refer to model). Maximum operating temperature 35°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2006042

Size:

4” suction fed inlet

Marking:

DAB, model and technical information on adhesive label on body.

Installation Requirements:

R001

Expiry date:

30/06/2025

Model:

Maximum working pressure 36.0 bar: S4 1/48 AMEIRA. S4 2/28 AMEIRA. S4 2/40 AMEIRA. S4 2/52 AMEIRA. S4 3/25 AMEIRA. S4 3/32 AMEIRA. S4 3/39 AMEIRA. S4 3/45 AMEIRA. S4 3/51 AMEIRA. S4 3/67 AMEIRA. S4 4/27 AMEIRA. S4 4/35 AMEIRA. S4 4/48 AMEIRA. S4 4/62 AMEIRA. S4 6/21 AMEIRA. S4 6/29 AMEIRA. S4 6/38 AMEIRA. S4 6/52 AMEIRA. S4 6/61 AMEIRA. S4 8/27 AMEIRA. S4 8/35 AMEIRA. S4 8/38 AMEIRA. S4 8/47 AMEIRA. S4 8/50 AMEIRA. S4 12/18 AMEIRA. S4 12/24 AMEIRA. S4 12/34 AMEIRA. S4 12/44 AMEIRA. S4 16/16 AMEIRA. S4 16/21 AMEIRA. S4 16/29 AMEIRA. S4 16/38 AMEIRA. Maximum working pressure 23.0 bar: S4 1/13 AMEIRA. S4 1/19 AMEIRA. S4 1/26 AMEIRA. S4 1/37 AMEIRA. S4 2/7 AMEIRA. S4 2/10 AMEIRA. S4 2/14 AMEIRA. S4 2/20 AMEIRA. S4 3/6 AMEIRA. S4 3/9 AMEIRA. S4 3/13 AMEIRA, S4 4/4 AMEIRA. S4 4/7 AMEIRA. S4 4/9 AMEIRA. S4 4/14 AMEIRA. S4 4/19 AMEIRA. S4 6/5 AMEIRA. S4 6/7 AMEIRA. S4 6/10 AMEIRA. S4 6/14 AMEIRA. S4 8/5 AMEIRA. S4 8/9 AMEIRA, S4 12/6 AMEIRA, S4 12/9 AMEIRA. S4 12/13 AMEIRA. S4 16/8 AMEIRA. S4 16/12 AMEIRA. S4 3/19 AMEIRA. S4 8/7 AMEIRA. S4 8/15 AMEIRA. S4 8/21 AMEIRA.

Approval Holder:

DAB PUMPS SPA

Company Name

DAB PUMPS SPA

Address

Via Marco Polo 14 Mestrino (PD)

Postcode

35035

Country

Italy

General Email

certifications@dwtgroup.com

View All Listings by this Company

VDROO range of stainless steel multistage centrifugal pumps with stainless steel impellers, diffusers and outer sleeves. The pumps incorporate a Silicone Carbide and EPDM mechanical seal. Maximum working pressure 25.0 bar DIN flange. Maximum working pressure 16.0 bar for oval flange. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2006303

Size:

DIN flange connections: DN25-50 Oval flange connections: 1” BSP (F) - 1½” BSP (F).

Marking:

Hydroo on adhesive label and on body. Hydroo, model, date of manufacture (YYYYMMDD) and other technical information on data label on body.

Installation Requirements:

R001 R415

Expiry date:

30/06/2025

Model:

VDROO Range: DIN flange connections: VX1 DN25 (stages 2-40). VX3 DN25 (stages 2-31). VX5 DN32 (stages 2-33). VX10 DN40 (stages 1-22). VX15 DN50 (stages 1-18). VX20 DN50 (stages 1-17). OVAL flange connections: VX1 G1” (stages 2-26). VX3 G1” (stages 2-21). VX5 G1¼” (stages 2-23). VX10 G1½” (stages 1-14). Designation example: VX1-XX-Y Where XX denotes stages and can be replaced by: Number of stages. Where Y denotes flange connection and can be replaced by: R – DIN flange connection. O – oval flange connection.

Approval Holder:

HYDROO PUMP INDUSTRIES S.L.

Company Name

HYDROO PUMP INDUSTRIES S.L.

Postcode

17843

Country

Spain

General Email

jordi.armengol@hydroo.com

View All Listings by this Company

Range of vertical multistage booster pumps, with stainless steel bodies and impellors (AISI304 or 316 see model). Maximum working pressure (model dependent): 4.0 bar models: BMVET(I) 32-10-1 to BMVET(I) 32-40. BMVET(I) 42-10-1 to BMVET(I) 42-20. BMVET(I) 65-10-1 to BMVET(I) 65-20-2. BMVET(I) 85-10-1 to BMVET(I) 85-10. 10.0 bar models: BMVET(I) 1-2 to BMVET(I)1-36. BMVET(I) 2-2 to BMVET(I) 2-11. BMVET(I) 3-2 to BMVET(I) 3-29. BMVET(I) 4-2 to BMVET(I) 4-10. BMVET(I) 8-2 to BMVET(I) 8-20. BMVET(I) 12-2 to BMVET(I) 12-18. BMVET(I) 16-2 t BMVET(I) 16-16. BMVET(I) 20-1 to BMVET(I) 20-17. BMVET(I) 32-50-2 to BMVET(I) 32-100. BMVET(I) 42-30-2 to BMVET(I) 42-50. BMVET(I) 65-20-1 to BMVET(I) 65-30. BMVET(I) 85-20-2 to BMVET(I) 85-30-2. 15.0 bar models: BMVET(I) 2-13 to BMVET(I) 2-26. BMVET(I) 3-31 to BMVET(I) 3-36. BMVET(I) 4-12 to BMVET(I) 4-22. BMVET(I) 32-110-2 to BMVET(I) 32-140. BMVET(I) 42-60-2 to BMVET(I) 42-130-2. BMVET(I) 65-40-2 to BMVET(I) 65-80-1. BMVET(I) 85-30-1 to BMVET(I) 85-60. Maximum operating temperature 100°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2009028

Note:

Claims for flow rate are made by the manufacturer and not considered part of the listing.

Size:

DN25 (Pumps with 1, 2 or 3 m³/h rated flow rates). DN32 (Pumps with 4 m³/h rated flow rates). DN40 (Pumps with 8 m³/h rated flow rates). DN50 (Pumps with 12, 16 or 20 m³/h rated flow rates). DN65 (Pumps with 32 m³/h rated flow rates). DN80 (Pumps with 42 m³/h rated flow rates). DN100 (Pumps with 65 or 85 m³/h rated flow rates).

Marking:

EFAFLU and other technical information on data plate. Flow arrow, PN and DN on body.

Installation Requirements:

R001 R415

Expiry date:

30/09/2025

Model:

BMVE T X - Y - Z. BMVE TI X - Y - Z. Model key: BMVE = Pump series name. T = Stainless Steel AISI304. TI = Stainless Steel AISI316. X = rated flow rate in m³/h (1, 2, 3, 4, 8, 12, 16, 20, 32, 42, 65, 85). Y = number of stages (2-140). Z = number of small impellors (blank, 1 or 2).

Product Images

Approval Holder:

EFAFLU BOMBAS E VENTILADORES S.A

Company Name

EFAFLU BOMBAS E VENTILADORES S.A

Phone

+351 252 298 700

General Email

geral@efaflu.pt

View All Listings by this Company

CM(E)(C) range of electronically operated pumps available in stainless steel, (‘EN 1.4301/AISI304’ or ‘EN 1.4401 /AISI316’) and cast iron. (CMEC models were added October 2023). The pumps are supplied with Sic-Sic mechanical shaft seals and FKM or EPDM seals. Cast iron models: Maximum working pressure 10.0 bar. Cold water use only. Stainless steel models: Maximum working pressure 16.0 bar. Maximum operating temperature 60°C for self-priming models, 99°C for all other models.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2011907

Size:

1” - 2” BSP (F) or NPT inlet and outlet.

Marking:

Grundfos and Grundfos logo, type, model and technical information on adhesive label either on the terminal box or fan cover.

Installation Requirements:

R001 R415

Expiry date:

30/11/2025

Model:

CM(E)(C)1, CM(E)(C)3 and CM(E)(C)5: CM(E)(C)1, cast iron / AISI304 2 – 8 stages. CM(E)(C)3, cast iron / AISI304 2 – 8 stages. CM(E)(C)5, cast iron / AISI304 2 – 8 stages. CM(E)(C)1, AISI316 2 - 14 stages. CM(E)(C)3, AISI316 2 - 14 stages. CM(E)(C)5, AISI316 2 - 13 stages. CM(E)(C)10 CM(E)(C)15 and CM(E)(C)25: CM(E)(C)10, cast iron / AISI304 1 – 5 stages. CM(E)(C)15, cast iron / AISI304 1 – 4 stages. CM(E)(C)25, cast iron / AISI304 1 – 4 stages. CM(E)(C)10, AISI316 1 – 8 stages. CM(E)(C)15, AISI316 1 – 4 stages. CM(E)(C)25, AISI316 1 – 4 stages. Self-priming models: CM(E)1, AISI316 3 – 6 stages (S or O) CM(E)3, AISI316 3 – 6 stages (S or O) CM(E)5, AISI316 3 – 7 stages (S or O) Model key: CM/CME/CMEC X1-X2 X3 X4-X5-X6-X7-X8 X9 X10 X11 X11-X12-X13-X14 Where: CM = Centrifugal Modular. CME = Centrifugal Modular with integrated frequency converter. CMEC = Centrifugal Modular with integrated frequency converter and only core functions of the motor unit. (NOTE: CMEC models were added October 2023). X1 = Rated flow rate at 50 Hz (m³/h): 1-25. X2 = Number of impellers: 1-14. X3 = Pump Versions: A - Basic Version. E: Pumps with certificates/approvals. O: Self-priming version (maximum suction lift 8 metres). S: Self-priming version (maximum suction lift 4 metres). X4 = Pipe connection: R: Rp (ISO 7/1). S: Internal Npt thread. X5 = Material in contact with pump media: A: inlets and outlets parts EN-GJL-200, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. G: Sleeve, Pump shaft + Impellers and chambers EN 1.4401/AISI 316. I: Sleeve, Pump shaft + Impellers and chambers EN 1.4301/AISI 304. X6 = Rubber parts in pump (excluding neck ring and shaft seal): E: EPDM. V: FKM. X7 = Shaft seal: A: O-ring seal with fixed driver. X8 = Material of rotating seal face: Q: Silicon Carbide (SIC). X9 = Material of stationary seal face: Q: Silicon Carbide (SIC). X10 =Material of secondary seal: E: EPDM. V: FKM. X11 = Supply voltage: B/B1/C/D/E/E1/F/G/H/I/J/O/S/T/U/V/X. X12 = Motor information: A/B/C/D/EF/G/H/I/J. X13 = Mains plug: A/B/C/D. X14 = Sensor: N: No sensor. Example: CM 10-3 A-R-I-E-A Q Q E C-A-A-N

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of pumps with either brass or stainless-steel bodies, stainless steel impellor and NBR ‘O’ rings. 20 & 33 brass series have a maximum working pressure of 16.0 bar. 33 stainless-steel series has a maximum working pressure of 20.0 bar. 22, 24 ,26, 38, 31, 32 & 34 series have a maximum working pressure of 20.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2101029

Size:

Please refer to model.

Marking:

Fluid-o-tech, logo and other technical info on adhesive label. Fluid-o-tech logo and flow arrow on body.

Installation Requirements:

R001 R415

Expiry date:

31/01/2026

Model:

20 series – Brass - TW030, TW031, TW034, TW034Z, TW050, TW051, TW054, TW054Z, TW070, TW071, TW074,TW074Z, TW100, TW101, TW104, TW104Z, TW150, TW151, TW154, TW154Z, TW180, TW181, TW184, TW184Z,TW200 , TW201, TW204, TW204Z – 3/8” GAS or 3/8” NPT (F) Inox - TW0310, TW0311, TW0314, TW0314Z, TW0510, TW0511, TW0514, TW0514Z, TW0710, TW0711,TW0714, TW0714Z, TW110, TW111, TW114, TW114Z, TW1510, TW1511, TW1514, TW1514Z, TW1810, TW1811,TW1814, TW1814Z, TW210, TW211, TW214, TW214Z – 3/8” GAS or 3/8” NPT (F) 22 series – Brass – PW070, PW071, PW071X, PW074, PW074Z, PW074X, PW074XZ, PW100, PW101, PW101X,PW104, PW104Z, PW104X, PW104XZ, PW150, PW151, PW151X, PW154, PW154Z, PW154X, PW154XZ, PW200,PW201, PW201X, PW204, PW204Z, PW204X, PW204XZ, PW250, PW251, PW251X, PW254, PW254Z, PW254X,PW254XZ, PW300, PW301, PW301X, PW304, PW304Z, PW304X, PW304XZ, PW350, PW351, PW351X, PW354, PW354Z,PW354X, PW354XZ, PW400, PW401, PW401X, PW404, PW404Z, PW404X, PW404XZ - 3/8” GAS or 3/8” NPT (F) Inox - PW0710, PW0711, PW0711X, PW0714, PW0714Z, PW0714X, PW0714XZ, PW110, PW111,PW111X, PW114 PW114Z, PW114X, PW114XZ, PW1510, PW1511, PW1511X, PW1514, PW1514Z, PW1514X,PW1514XZ, PW210, PW211, PW211X, PW214, PW214Z, PW214X, PW214XZ, PW2510, PW2511, PW2511X, PW2514,PW2514Z, PW2514X, PW2514XZ, PW310, PW311, PW311X, PW314, PW314Z, PW314X, PW314XZ, PW3510,PW3511, PW3511X, PW3514, PW3514Z, PW3514X, PW3514XZ, PW410, PW411, PW411X, PW414, PW414Z PW414X, PW414XZ - 3/8” GAS or 3/8” NPT (F) 24 series – Brass – CW031, CW034, CW034Z, CW051, CW054, CW054Z, CW071, CW074, CW074Z, CW101, CW104, CW104Z, CW151, CW154, CW154Z, CW181, CW184, CW184Z, CW201, CW204, CW204Z - 3/8” GAS or 3/8” NPT (F) 26 series – Brass – MW030, MW031, MW034, MW034Z, MW050, MW051, MW054, MW054Z, MW070, MW071, MW074,MW074Z, MW100, MW101, MW104, MW104Z, MW150, MW151, MW154, MW154Z, MW180, MW181, MW184,MW184Z, MW200, MW201, MW204, MW204Z - 3/8” GAS or 3/8” NPT (F) Inox - MW0310, MW0311, MW0314, MW0314Z, MW0510, MW0511, MW0514, MW0514Z, MW0710,MW0711, MW0714, MW0714Z, MW110, MW111, MW114, MW114Z, MW1510, MW1511, MW1514, MW1514Z, MW1810,MW1811, MW1814, MW1814Z, MW210, MW211, MW214, MW214Z - 3/8” GAS or 3/8” NPT (F)

28 series – Brass – PW500, PW501, PW504, PW600, PW601, PW604, PW700, PW701, PW704, PW800, PW801, PW804, PW900, PW901, PW904, PW1000, PW1001, PW1004 – 1/2” GAS or 1/2” NPT (F) Inox - PW510, PW511, PW514, PW610, PW611, PW614, PW710, PW711, PW714, PW810, PW811,PW814, PW910, PW911, PW914, PW1010, PW1011, PW1014 - 1/2” GAS or 1/2” NPT (F) 31 series – Inox -TSFRSS070AW, TSFRSS071AW, TSFRSS074AW, TSFRSS100AW, TSFRSS101AW,TSFRSS104AW, TSFRSS150AW, TSFRSS151AW, TSFRSS154AW, TSFRSS200AW, TSFRSS201AW,TSFRSS204AW, TSFRSS250AW, TSFRSS251AW, TSFRSS254AW, TSFRSS300AW, TSFRSS301AW,TSFRSS304AW, TSFRSS350AW, TSFRSS351AW, TSFRSS354AW, TSFRSS400AW, TSFRSS401AW, TSFRSS404AW - 3/8” NPT (F) 32 series – Brass – TMFROT030AW, TMFROT031AW, TMFROT034AW, TMFROT050AW, TMFROT051AW, TMFROT054AW, TMFROT070AW, TMFROT071AW, TMFROT074AW, TMFROT100AW, TMFROT101AW, TMFROT104AW, TMFROT150AW, TMFROT151AW, TMFROT154AW, TMFROT180AW, TMFROT181AW, TMFROT184AW, TMFROT200AW, TMFROT201AW, TMFROT204AW - 3/8” NPT (F) Inox - TMFRSS030AW, TMFRSS031AW, TMFRSS034AW, TMFRSS050AW, TMFRSS051AW, TMFRSS054AW, TMFRSS070AW, TMFRSS071AW, TMFRSS074AW, TMFRSS100AW, TMFRSS101AW, TMFRSS104AW, TMFRSS150AW, TMFRSS151AW, TMFRSS154AW, TMFRSS180AW, TMFRSS181AW,TMFRSS184AW, TMFRSS200AW, TMFRSS201AW, TMFRSS204AW - 3/8” GAS (F) 33 series – Brass – TW500, TW501, TW504, TW600, TW601, TW604, TW700, TW701, TW704, TW800, TW801, TW804, TW900, TW901, TW904, TW1000, TW1001, TW1004 – 1/2” GAS or 1/2” NPT (F) Inox - TW510, TW511, TW514, TW610, TW611, TW614, TW710, TW711, TW714, TW810, TW811, TW814, TW910, TW911, TW914, TW1010, TW1011, TW1014 – 1/2” GAS or 1/2” NPT (F) 34 series - Inox - TW310, TW311, TW314, TW410, TW0411, TW0414 - 3/8” GAS or NPT (F)

Product Images

Approval Holder:

Fluid-o-Tech (Italy) & Fluid-o-Tech Asia (Shanghai) Co. Ltd.

Company Name

Fluid-o-Tech (Italy) & Fluid-o-Tech Asia (Shanghai) Co. Ltd.

View All Listings by this Company

Manufacturer:

Fluid-o-Tech (Italy) & Fluid-o-Tech Asia (Shanghai) Co. Ltd.

Company Name

Fluid-o-Tech (Italy) & Fluid-o-Tech Asia (Shanghai) Co. Ltd.

View All Listings by this Company

Range of wall mounted shower outlets with brass bodies (various finishes). The 24 004 xxx, 24 014 xxx and 35 279 xxx models are supplied with ceiling mounted shower arm. The 24 005 xxx, 24 015 xxx, 35 275 xxx and 35 280 xxx supplied with wall mounted shower arm. The 24 005 xxx, 24 015 xxx, 35 275 xxx & 35 280 xxx models incorporate stainless steel strainers on the inlet. The 24 014 xxx & 24 015 xxx models incorporate plastic flow regulators on the inlet. Maximum operating temperature 60°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2006045

Marking:

24 004 xxx, 24 014 xxx, 24 005 xxx & 24 015 xxx models: Hansgrohe on faceplate. 35 275 xxx, 35 279 XXX & 35 280 xxx models: AXOR on faceplate.

Installation Requirements:

R001 R040

Expiry date:

30/06/2025

Model:

The following models are for use with the 24 010 180 Hansgrohe Rainmaker Select basic set overhead shower ceiling connector: 24 24 004 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower with ceiling connector 100 mm). 24 014 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower EcoSmart 9 l/ min with ceiling connector 100 mm). 35 279 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with ceiling connector). The following models are for use with the 01 800 180 Basic set iBox universal: 24 005 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower with shower arm 450 mm). 24 015 xxx Hansgrohe Rainmaker Select 460 (2jet overhead shower EcoSmart 9 l/min with shower arm 450 mm). 35 275 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with shower arm and softcube escutcheons). 35 280 xxx AXOR ShowerSolutions Overhead shower 460 / 300 (2jet with shower arm and square escutcheons). with rough 01800180 Where xxx denotes the surface finish, which can be replaced by any combination of numbers and/or letters. As examples, but not limited to: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.

Approval Holder:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company

Manufacturer:

Hansgrohe SE

Company Name

Hansgrohe SE

Address

Auestrasse 5 - 9, Schiltach

Postcode

77761

Country

Germany

Phone

+49 170 4471 718

General Email

Ludovic.hauer@hansgrohe.com

View All Listings by this Company