'WRC EPDM 92645'. Black coloured EPDM liner manufactured by calendaring. Shore hardness 80 A. Tested in-radius size 0.5mm. For use with water up to 23°C.
'ME0940 'O' rings'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 5.0mm. For use with water up to 85°C.
'F3352'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 0.65mm. For use with water up to 85°C.
'01/B70NBR Gaskets and 'O' rings'. Black coloured, injection moulded NBR Gaskets and 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 23°C.
'KF945W, KF955W, KF965W & KF975W'. Black coloured, compression moulded, silicone rubber materials. Shore hardness between 45 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SIL70 Red 'O' rings'. Red coloured, injection moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 1.35mm. For use with water up to 85°C.
'GEBSOPLAST® MAX'. White coloured (opaque) solvent cement. Apply as per manufacturer's TDS and cure for 24 hours@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of stop valves with plastic bodies. The valves incorporate a built-in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with models SVSM66MRD & SVSM44MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. Please note that claims of leak detection have not been verified by WRAS For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only.
Range of single-hole, multiple outlet, swivel, (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-down spray outlet incorporating a plastic aerator. Maximum working pressure: 10.0bar Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies. Incorporating a solenoid valve activated via an infra-red sensor. The inlets to the control box incorporate stainless steel strainers and the outlet incorporates a plastic aerator. Maximum working pressure: 8 Bar Maximum operating temperature: 65°C
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Non-verifiable single check valve assembly with chrome plated DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headworks with a lever type operating member. The spout outlet incorporates a metal aerator. The product is supplied with a lever type pop up waste. Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals and NBR O-rings. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn Ceramic disc headworks with brass bodies incorporating NBR rubber seals. For insertion into specifically dimensioned bores Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Some models incorporate a stainless-steel strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a single sequential cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a single sequential headwork with a single lever operating member. The spout outlet incorporates a plastic aerator and the product is supplied with a pop-up waste. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
Page 383 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
