Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘TAQ’ range of stainless steel or grey nylon braided (indicated by ACB in model name), EPDM lined flexible hose assemblies, incorporating various end connections. Some of the possible end connections also incorporate EPDM washers, gaskets or ‘O’-rings. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of stainless steel indirect (single or twin coil), direct and heat pump unvented hot water storage cylinders. The heat pump models also incorporate a plate heat exchanger and a circulation pump. The secondary circuit is supplied with a temperature and pressure relief valve set at 7.0 bar@90.0˚C. The products are supplied with an inlet control group consisting of an adjustable pressure reducing valve, adjustable in the range of 0.8 bar - 6.0 bar, but factory pre-set at 3.0 bar, a strainer, am expansion relief valve set at 6.0 bar and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The products are also supplied with an immersion heater, an expansion vessel (12, 19 or 24 litres depending on model) and a tundish. Maximum supply pressure to the inlet control group: 16.0 bar. Maximum working pressure: Secondary circuit: 5.5 Bar. Primary Circuit: 6.0 Bar (All models except for the Direct - DI prefix models). Maximum operating temperature 75°C.
Range of air vent valves with brass (covered with blue polyester coated ductile iron body) or plastic bodies and plastic floats. Maximum working pressure 16.0 bar (AP models) or 25.0 bar (AQ models). Cold water use only.
Range of automatic air venting valves incorporating epoxy coated, ductile iron bodies and plastic float. Maximum operating pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 50°C
Range of automatic air venting valves with brass bodies, stainless steel strainer, plastic float and EPDM ‘O’-rings and gaskets. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of wall mounted concealed blending valves with brass bodies. Incorporating a thermostatic mixing valve with a single lever operating member controlling the temperature to 2 separate outlets. The product incorporates approved single check valves on the inlets; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Wall mounted thermostatic shower valve (brass body, matt black finish), incorporating a quarter turn ceramic disc headwork diverting the flow between overhead shower and handset with dome type operating member. Temperature is controlled independently via a thermostatic cartridge with a dome type operating member that incorporates a manual override button. The product incorporates a fixed riser and overhead shower and is supplied with a shower hose and handset. Both inlets incorporate stainless steel strainers and approved check valve cartridges, however, the complete products have not been fully tested to demonstrate that they provide backflow protection. Maximum working pressure: 5.0 Bar Maximum operating temperature: 60°C
Shower kit consisting of a wall mounted thermostatic blending valve incorporating a (brass body, matt black finish), quarter turn ceramic disc headwork controlling the flow, the temperature is controlled via a thermostatic cartridge which incorporates a manual override button and dome type operating members. Each inlet incorporates a combined EPDM washer with stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with shower hose, shower handset, riser rail. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, bar type thermostatic blending valves incorporating a quarter turn ceramic disc headwork or half turn ceramic diverter controlling the flow between outlets. The temperature is controlled by a thermostatic cartridge with various type of operating members incorporating a manual override button. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Page 374 of 1010
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
