'FY Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'FR20240910', dated '2024-09-10'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Purtop 1000 N'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS '7506-3-2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DPFC GRE Pipe'. Yellow-brown coloured GRE pipe manufactured by filament winding. For use with water up to 70°C.
'Turmsilon GL 320-G'. White coloured silicone grease/lubricant. For use with water up to 85°C.
‘DENYL 6 5010 NERO 0300, DENYL 6 3010 NERO 0300, DENYL 6 1510 NERO 0300, DENYL 6 5010 NERO, DENYL 6 3010 NERO & DENYL 6 1510 NERO’. Black coloured, injection moulded, glass fibre filled PA6 materials. For use with water up to 85°C.
'Vicnyl 25G60 BK003, Vicnyl 25G60 NC003, Vicnyl 25G60XF BK003 & Vicnyl 25G60XF NC003'. Natural (appears cream) or black coloured, injection moulded PPA materials. For use with water up to 85°C.
'GF PROGEF PP Pipe'. Beige coloured, extruded PP-H pipe. For use with water up to 80°C.
'Xtreme Tape'. Extruded, self-fusing silicone rubber tapes available in Black and Red colours. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
'Xtreme Tape'. Extruded, self-fusing silicone rubber tapes available in Clear and Bright Red colours. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 85°C.
'EP11/8/3 BLK'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
'E13970'. Black coloured, injection moulded EPDM material. Shore hardness 65. Tested in-radius size 1.3mm. For use with water up to 23°C.
'NB01280PWRC'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ERIKS 366207'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'NB012370P(KAWN)'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'HTA Brown CPVC Fittings'. Brown coloured, injection moulded CVPC fittings. For use with water up to 70°C.
'HTA-F Orange CPVC Pipe & HTA Brown CPVC Pipe'. Extruded, CPVC pipes. For use with water up to 70°C.
Bottom entry A1370A and side entry A1423B BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. A1270A - plastic or brass connector. A1423B - plastic connector only. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted single hole, single outlet (fixed), combination tap assembly (various plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet with a dome type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (swivel nozzle) combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with cross top or lever type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure - 5 Bar Maximum operating temperature - 60 °C
Range of ceramic cartridge headworks with a plastic body, incorporating silicone seals. The products are intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 17.5 bar. Maximum operating temperature 70°C.
Page 374 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
