'Vandex Super'. Site applied, two-component, grey coloured (once mixed) cementitious coating. Mix cement powder with water in a weight ratio of 5:2. Apply as per manufacturer's Instructions for Use '2nd issue', dated '18.11.2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘Sikalastic P 770’ (formerly known as ‘MasterSeal P 770’) Primer for use with ‘Sikalastic M 808’ (formerly known as ‘MasterSeal M 808 Grey’, and ‘MasterSeal M 808 Light Grey’) topcoats. Site applied coating system, which is light grey coloured (once mixed and applied), comprising of a primer and polyurethane coatings. Coat 1 primer: Mix parts A & B of ‘Sikalastic P 770’ Primer in a weight ratio of 2.2:2.8. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 24 hours@7°C. Coat 2 (coating): Mix parts A & B of ‘Sikalastic M 808’, dark grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 6 hours@7°C. Coat 3 (water contact coating): Mix parts A & B of ‘Sikalastic M 808’, light grey coloured (once mixed) polyurethane coating in a weight ratio of 3.3:1.7. Apply as per manufacturer’s IFU ‘version No. 1’, dated ‘22nd November 2024’. Cure for 7 days@7°C. When applying the coating system to GRP there is no need to apply a primer. Mix, apply and cure ‘Sikalastic M 808’ dark grey and then mix, apply and cure ‘Sikalastic M 808’ light Grey (water contact layer) as detailed above. For use with water up to 23°C.
‘Intergard 269 & Interline 975’. Site applied, white coloured Epoxy coating system comprising of a base coat and a topcoat. ‘Intergard 269’ is a two-component base coat which comprises of Part A (red/brown coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 7.46:1 and apply as per manufacturer’s TDS ref. ‘206’, dated 08/02/2021. Cure for 12 days@25°C. ‘Interline 975’ is a two-component topcoat which comprises of Part A (white coloured) and Part B (straw coloured). Mix Part A & Part B in a mass ratio of 3.12:1 and apply as per manufacturer’s TDS ref. ‘3577’, dated 31/07/2017. Cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CanSEALER (CS1)-TS'. Site applied, colourless waterproofing sealer which can be applied to cement with a roller or a brush. Apply one coat with a roller or a brush as per manufacturer's Technical Data Sheet 'CS1-210002'. Cure for 36 days@5°C. When applied by brush the material is for use with water up to 23°C. When applied by roller the material is for use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`BELPA CSA 90`. Pink coloured fibre gasket material manufactured by calandering. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Klingersil® C-4240'. Fibre gasket material, manufactured by calendaring, which is beige coloured on one side and off-white coloured on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'TPU inner hose (YOUSHI/3017)'. Transparent, colourless, extruded TPU hose. For use with water up to 85°C.
`VIP Universal Pipe Lubricant`. Translucent, amber coloured, soya oil lubricant. Apply as per manufacturer's technical datasheet issued 'Nov 2019'. For use with water up to 23°C.
'Zytel® FG101L NC010 & Zytel® FG42A NC010'. Un-pigmented (appear off-white, translucent), injection moulded nylon materials. For use with water up to 23°C.
'Zytel® HTNFG52G35HSLR BK011'. Black coloured, injection moulded polyphthalamide (PPA) material. For use with water up to 85°C.
Page 356 of 1132
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
