Range of gate valves with blue epoxy coated ductile iron bodies and disks, with EPDM O seats. The valves are operated via a non-rising spindle headwork and hand wheel. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising spindle lock shield gate valves with DZR brass bodies. Maximum working pressure 16 bar. Maximum operating temperature: 65°C Maximum working pressure 10 bar. Maximum operating temperature: 82°C
Range of non-rising spindle gate valves with bronze bodies and wedges incorporating PTFE seals and a handwheel type operating member. Maximum working pressure and operating temperature: 16.0 bar @ 65°C. Maximum working pressure and operating temperature: 10.0 bar @ 82°C.
Range of gate valves with brass bodies and gates incorporating hand wheel type operating member. Max working pressure and operating temperatures: 16.0 bar at 65°C. Max working pressure and operating temperatures: 10.0 bar at 82°C.
Screw down stop valve, with brass body, HDPE seat and handwheel operating members. Maximum working pressure 10 bar. Cold water use only.
Range of press fit screw down stop valves with brass bodies incorporating EPDM seat washers, PTFE seals and non-rising spindles operated via ‘T’ type operating members For use with copper tube to BS EN 1057. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
‘MagCat’ range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Electrolytic scale reducer, with a chromium plated copper body and zinc alloy anodes, for use with copper pipe (manufactured to BS EN1057) Maximum working pressure 10.0 bar. Cold water use only.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
'DURACON®M90-44 WK3068'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'KEPITAL F10-03H BBK & KEPITAL F10-03H BK'. Black coloured, injection moulded POM materials. For use with water up to 85°C. 'KEPITAL F10-52H'. Natural (appears white), injection moulded POM material. For use with water up to 40°C.
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIANYI SUNS-012'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's user instructions 'File No.: Tianyi Suns-0024, Version: TYS-03, Date of issue: 2021-05-05'. Cure for 2 hours @60°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions reference 'XA12312', dated 26/12/2022. Cure for 15 minutes@220°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'PPA571ES Black 700 & PPA571 Black 700'. Factory applied Polyolefin PE Coatings. Apply 'PPA571 Black 700' by fluidised bed according to manufacturer's data sheet '08/2022' and dip in the bed for 5-8 seconds. Apply 'PPA571ES Black 700' by electrostatic spray according to manufacturer's data sheet '08/2022'. Cure for 190-200°C for 20 mins. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL035P Interpon 100 Gloss Light Grey'. Factory applied, light grey coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'Interpon 100 -AL035P - Issue #01', revision date '20.07.2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'CY7000 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instruction manual 'YS-QNS-WZBC-2021W', dated 'May 20, 2021'. Cure for 15 minutes@180°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
Page 343 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
