Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coating ductile iron bodies and wedges and EPDM ‘O’-rings. The valves operate using a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 16.0 Bar. Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with bronze bodies, bronze wedge and PTFE washers. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of screw-down stop valves with brass bodies, incorporating a non-rising spindle operated via a T shaped (all models excluding 513042) or hand wheel operating member (model 513042 only) and EPDM seats. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of screw down stop valves with brass bodies and EPDM gaskets. M profile press connection to be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of screw down angle valves (chromium plated brass) incorporating a dome or triangular type operating member with a NBR washer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 8.6 bar. Cold water use only.
Range of undercounter water chillers with a stainless-steel cooling tank including a drain outlet. Maximum working pressure 3.0 Bar. Maximum operating temperature 38°C.
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valcoat Blue'. Factory applied, blue coloured epoxy coating. Pre-heat the substrate and apply as per manufacturer's TDS with issue '01.04.2023'. Post-cure for 5-7 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'TM-cement-01'. Factory applied, grey coloured cement. Mix sand/cement/water in a weight ratio of 1.7:1.0:0.74 and apply as per manufacturer's instructions 'TM20231122-A0', dated 2023-11-22. Cure for 6 hours@25°C (±2°C). Between November 2023 and November 2024, the material was for use with water up to 23°C. Between December 2024 and November 2028, the material is for use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JDFF epoxy powder coating’. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s instructions (Procedure #: Pc-01-3, Work Instruction #: JDFF WI-Pc-01-3-1, Revision #: 2, Issue #: 5, date: 10-01-2023). Cure for 2½ minutes at 232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions reference 'XA12312', dated 26/12/2022. Cure for 15 minutes@220°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
Page 327 of 584
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
