'OLD ETP890 70N'. Black coloured, injection moulded EPDM rubber. Shore hardness 70. Tested in-radius size 1.11mm. For use with water up to 85°C.
'3E60B11P & 3E70B03P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SU26F415H01 'O' ring'. Black coloured, compression moulded FKM rubber 'O' ring. Shore hardness 80. Tested in-radius size 0.9mm. For use with water up to 75°C.
'V8 Fluorocarbon Rubber Bellows'. Black coloured, injection moulded fluorocarbon rubber bellows. Shore hardness 70. Tested in-radii sizes between 0.7mm & 4.1mm. For use with water up to 85°C.
'Silicone Rubber Washer SIL40 (SIL4001)'. Black coloured, vulcanised silicone rubber washer. Shore hardness 40. Tested in-radius size 0.56mm. For use with water up to 85°C.
'Type 1 O-ring, T056D 124H16 Model Code P16'. Cream coloured (opaque), compression moulded silicone rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Loctite 5800'. Red coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated April 2012. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Penosil PVC Pipe Adhesive 935 & Penosil Adhesivo PVC-U A-35'. Clear (transparent) solvent cements intended to join PVC pipe and fittings. Apply as per manufacturers technical data sheet. Cure for 48 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies. Incorporating a solenoid valve activated via an infra-red sensor. The inlets to the control box incorporate stainless steel strainers and the outlet incorporates a plastic aerator. Maximum working pressure: 8 Bar Maximum operating temperature: 65°C
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of electronic combination tap assemblies, incorporating a solenoid valve controlling the flow that is activated via an infra-red sensor. The Xeris models (012930699 & 012940699) incorporate a check valve cartridge in the inlet hose, however the complete assembly has not been tested to demonstrate it provides backflow protection. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Concealed BS EN 14055: 2018 WC flushing cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a dual or single flush pneumatic drop valve capable of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by touch free electronic or manual push button / push plate options. Maximum working pressure 10.0 bar. Cold water use only.
Non-Verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated DZR brass body. The assembly incorporates an isolation valve. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.
Range of non-verifiable double check valve assemblies consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body with nickel plated or natural finish. Models with compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Models 12.10152.015.CP02-8511 & 12.10152.015.CP5R-8511 have a maximum operating temperature of 65°C. All other models have a maximum operating temperature of 85°C
Non-verifiable double check valve assembly with DZR brass body (chrome plated), incorporating two in-line check valve cartridges. Maximum working pressure – 10.0 Bar Maximum operating temperature - 85°C
Non-verifiable, double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a nickel plated, DZR brass body. The assembly incorporates an isolation valve and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of non-rising spindle headworks with a brass body and EPDM ‘O’-rings. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure: 10.0 Bar. Maximum operating temperature: 85.0°C.
Page 304 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
