Range of stop valves with brass bodies and T-type operating members. Compression connecitons are for use with copper pipes (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of manually operated balancing valves incorporating bronze bodies, rising spindle balancing mechanism, EPDM washer & ‘O’-rings with either a metal or rubber seat. Maximum working pressure 10.0 Bar Maximum operating temperature 100.0°C
Range of magnetic scale reducers with metal bodies, for use with copper pipe (manufactured to EN 1057). Maximum working pressure 12 Bar. Maximum operating temperature 30°C.
Range of polyethylene pressure vessels with spun fibreglass casing. Maximum working pressure 10.0 bar Maximum operating temperature 50°C.
'YHR-GFS Enamel'. Factory applied, dark blue coloured Enamel coating. Mix enamel powder with water in a ratio of 7:3 and apply two coats as per manufacturer's TDS 'YHRGFS2504', version 'V0', dated '2025/3/27'. Cure for 20 minutes@120°C and fire for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the mixing, curing & firing conditions that appear on the approval. If the mix and/or cure and/or fire conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fusion Bonded Epoxy (IMP-FBE) Cobalt Blue RAL 5013'. Factory applied, dark blue coloured epoxy coating. Pre-heat the substrate to 200°C and spray apply one coat at 120°C as per manufacturer's TDS 'YHRFBE2504', version 'V0'. dated '2025/3/27'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EPLAMID HT00 GFR 40 FW BK'. Black coloured, injection moulded, glass fibre reinforced PA 6T/6I material. For use with water up to 85°C.
'ELTEX® SUPERSTRESS TUB124N6000'. Blue coloured, compression moulded HDPE material. For use with water up to 23°C.
'RAMSET ChemSet™ Reo502™ Xtrem™’ & ‘RAMSET ChemSet™ Epcon™ G5 Xtrem™'. Site applied, brick coloured (once mixed), chemical anchor resins, each supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'NOV. 25'. Cure for 24 hours@21°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP2504 (NSF)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.20mm. For use with water up to 85°C.
'Fernox LS-X'. Clear, silicone sealant. Apply as per manufacturer's technical data sheet dated 10-05-2021. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions 'PLUMEFF', dated '2024/09/17'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of floor mounted, single hole, single outlet combination tap assemblies (stainless steel body – various finishes) incorporating a ceramic cartridge headwork and manual diverter to shower outlet, with single lever operating members. The spout outlets incorporate a plastic aerator. Product incorporates an approved check valve cartridge at the inlet; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Shower hose and handset is not supplied with this product. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| F9920-** | Various | 1/2" Captive nut | 10 bar | 60 °C | LAN BIAO | Handle | No | Ceramic cartridge | Not Applicable | Aerator |
**Representing different surface color treatments： No Suffix = Chrome, H: Black DYB: Matte White BZ: Pearl White HGTS: Red Antique Bronze HTL: Yellow Bronze Brushed Q: Bronze QTSL: Bronze Brushed Bright QTS: Bronze Brushed Matte STS: Acid Copper Brushed SDMGJ: Water-Plated Rose Gold N: Nickel Brushed Bright NP: Nickel Brushed TJ: Titanium Gold TJLS: Titanium Gold Brushed G: Zirconium gold GJS: Zirconium Gold Brushed GJSY: Zirconium Gold Brushed Matte PGJFY: Zirconium Gold Brushed Bright PLSJ: Brushed Gold LSJY: Brushed Gold Matte MGJ: Rose Gold MGJL: Rose Gold Brushed DMGJ: Light Rose Gold Brushed HTS: Red Copper Brushed QHP: Gunmetal Gray LSQH: Gunmetal Gray Brushed LHMGJ: Brushed Yellow Rose Gold
Single hole, single outlet (fixed) electronically operated tap assemblies incorporating brass bodies (various finishes). Flow is controlled by solenoid valve and actuated by a touch sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 7.5 bar. Maximum operating temperature 60°C.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TVW105112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW103112111XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW125003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008002XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW107008003XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106003001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW111002001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVZ106010001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW112007001XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator | ||
| TVW116001000XX | Various | ½” BSP (F) inlets (A1313NU- core valve unit) | 10 bar | 60 °C | Villeroy & Boch | On the lever | Yes | Ceramic cartridge | Aerator |
XX at the end indicates the Finish of surfaces that are not in contact with water (61 - Chrome, K5 - Matt black, 76 - Brushed gold, 64 - Brushed nickel).
Wall mounted, fixed, spout outlet (brass bodies – various finishes) incorporating a plastic flow straightener. Maximum operating temperature 60°C Maximum working pressure: Open outlet use only
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 30 090 8xx | Various | G 1/2" | 10 bar | 65 °C | AXOR | on the nut | Yes | Not applicable | Not Applicable | Not Applicable | Shower Hose, |
Where 8xx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Page 302 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
