'18521 Kanepox Lining Free Blue for use with Kanepox Hardener 0362'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix 18521 Kanepox Lining Free Blue & Kanepox Hardener 0362 in a 3.5:1 volume ratio and apply as per manufacturer's datasheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikagard®-180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180_05_18/v9/02_22/v10/05_23/v11/01_24'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE® SF 770™' (known as 'LOCTITE 770'). Site applied, clear cyanoacrylate primer. Apply as per manufacturer's technical data sheet dated May 2021. Cure for 30 seconds@20°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Subcote FLP II’. Site applied, two-component, green coloured (once mixed and applied) Polyurethane coating. Mix parts A & B in a 100:72 weight ratio and apply & then flush as per manufacturer's IFU 'IFU_Subcote FLP II_In-Situ Pipes_Issue 7_210921 RS EN'. Cure for 1 hour@3°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Strongcoat EPW-P'. Site applied, two-component, light grey coloured (once applied) epoxy coating. Mix Part A (light grey coloured liquid) with Part B (orange coloured liquid) in a 8.1:3.78 volume ratio and apply coat 1 as per manufacturer's TDS 06-0020-A-2021. Cure for 24 hours@23°C. Mix and apply coat 2 in the same way as coat 1 and cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika Monotop 1010’ primer for use with ‘Sika Monotop 4012’ cement mortar. Site applied, grey coloured cementitious, polymer modified coating material used as bonding primer and cementitious, fibre reinforced, low shrinkage repair mortar. First coat: Mix 25kg ‘Sika Monotop 1010’ with 5.25 litres of water and apply as per manufacturer’s ‘Sika Monotop 4012' IFU issue no. ‘001’ dated ‘July 2022’. Second coat: Mix 25kg ‘Sika Monotop 4012’ with 3.8 litres of water and apply immediately to the first coat as per manufacturer’s IFU issue no. ‘001’ dated ‘July 2022’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TECHNYL ® SAFE C 216WFC V30 NC, TECHNYL ® SAFE C 216WFC V50 NC, TECHNYL ® SAFE C 216WFC V30 BK & TECHNYL ® SAFE C 216WFC V50 BK'. Natural (appears white) and black coloured, injection moulded, filled Polyamide 6 materials. For use with water up to 85°C.
‘TECHNYL ® SAFE A 219WFC V50 BK’. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
XYRON™ WG725 AWY2139 (off-white). XYRON™ WG725 AWY6633 (beige). XYRON™ WG725 AWY3328 (black) XYRON™ WG735 AWY3327 (black) XYRON™ WG735 AWY2138 (grey). XYRON™ WG735 AWY2272 (grey) XYRON™ WG735 AWY6632 (beige). Injection moulded, Modified Polyphenylene Ether materials. For use with water up to 85°C.
Page 302 of 350
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
