Range of regulating balancing valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of bedpan washers and macerators with flow controlled by solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid cat 5). Maximum working pressure 6 Bar Maximum operating temperature 60°C
‘Caleffi Ecal’ electrolytic anti-scale device with a stainless-steel filter and magnet, comprising of an in-line DZR brass body and a plastic housing. Maximum working pressure 16.0 bar. Maximum operating temperature 40°C.
Range of floor standing or wall mounted water dispensers which dispenses ambient and/or chilled water. Flow is controlled via self-closing headwork and products have either tap with lever operating members, a tap with floor pedal (floor standing models only), a bubbler with push button or a bubbler with floor pedal (floor standing models only). Maximum working pressure 6.0 bar. Cold water use only.
‘SIKAFLOOR 150 & SIKALASTIC-836 DW’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of SIKAFLOOR 150 in a 100:50 weight ratio and apply as per manufacturer’s PDS ‘October 2023, Version 11.0’. Cure for 4 hours@25°C. Mix parts A & B of SIKALASTIC-836 DW in a 100:100 volume ratio and apply as per manufacturer’s PDS ‘July 2022, Version 04.0’. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EPACRETE EPAPOX 25 & EPAPROOF FPCS WFC’. Factory applied, off-white coloured (once mixed and applied), two-part epoxy primer for use with two-part polyurea coating. Mix parts A & B of EPACRETE EPAPOX 25 in a 100:50 weight ratio and apply as per manufacturers TDS 01.140317. Cure for 4 hours@25°C. Mix parts A & B of EPAPROOF FPCS WFC in a 100:100 volume ratio and apply as per manufacturers TDS rev 01-2023. Cure for 24 hours@25°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaGrout-800'. Site applied, grey coloured Cementitious grout. Mix grout and water in an 8:1 weight ratio and apply as manufacturer's IFU 'Issue No.: 1', issued 'July 2024'. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versilon™ C-544-A I.B'. Triple layered, extruded tube consisting of a transparent (clear) polyurethane inner layer, white coloured polyester middle layer & transparent (clear) polyurethane outer layer. For use with water up to 65°C.
'Union Pipes Industry – K.S.A. HDPE Pipe' (made using BorSafe™ HE3490-LS, Hostalen CRP 100 Black, SABIC® HDPE P6006AD or TASNEE PE 100 black). Black coloured (with blue external stripes), extruded HDPE pipes. For use with water up to 60°C.
'B1-4773' Lip Seals and 'O' rings. Black coloured, EPDM components with shore hardness of 70. Compression moulded Lip Seals have an in-radius size of 2.7mm. Compression moulded ‘O’ rings have an in-radius size of 1.5mm. Injection moulded ‘O’ rings have an in-radius size of 1.0mm. For use with water up to 85°C.
'VEV1'. Black coloured, compression moulded FKM seal. Shore hardness 70 A. Tested in-radius size 4.45mm. For use with water up to 23°C.
'FKM 70 514404'. Black coloured, compression moulded FKM 'O' ring. Shore hardness 70. Tested in-radius size 5.0mm. For use with water up to 85°C.
'Weld-On 719 Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '719-05-2024'. Cure for 8 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 795 Blue PVC Cement'. Blue coloured solvent cement. Apply as per manufacturer's data sheet '795-05-2024'. Cure for 4 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 705 ECO Gray PVC Solvent Cement'. Grey coloured solvent cement. Apply as per manufacturer's data sheet '705 ECO-09-2024'. Cure for 12 hours at 5°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of wall mounted single hole, single outlet (fixed) electronically controlled combination tap assemblies (stainless steel spout, available in Satin, Stainless-Steel, Black, Brass, Bronze, Copper, and Chrome finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor which incorporates a stainless steel filter at its inlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60˚C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and a plastic flow regulator at the inlet. Maximum working pressure 10.0 Bar Cold water use only
BS EN 14055: 2018 concealed WC cistern incorporating a side or bottom entry compact type float operated inlet valve providing a Type AG air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
BS EN 14055: 2018 concealed WC cistern incorporating a side entry compact type float operated inlet valve providing a Type AB air gap with a pneumatic or cable operated drop valve capable of full flush volumes of up to 6 litres and reduced flush of up to 4 litres. The cistern can be operated by manual push button / push plate, (not supplied). Maximum working pressure 10.0 bar. Cold water use only.
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Wastes | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 58 130 xx0 | Various | G 1/2" | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 42 540 xx0 | Various | G 1/2" | open outlet bar | 65 °C | AXOR | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 119 xx0 | Various | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 131 xx0 | VArious | basic set 58152180 | open outlet bar | 65 °C | hansgrohe | on faceplate | Yes | Not applicable | Not Applicable | Open Outlet | Click Type | |
| 58 152 180 | NA | G 1/2" | open outlet bar | 65 °C | hansgrohe | sticker only, marking will be on the finish set | Yes | Not applicable | Not Applicable | Open Outlet |
model 58131xx0 and 58119xx0 are identical in the water pathway, only difference is the cover plate design. model 58130xx0 and 42540xx0 are both composed of the finish set 58131xx0/58119xx0 and basic set 58152180, only difference is the marking on the faceplate 58130xx0= hansgrohe, 42540xx0= AXOR
Page 292 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
