Range of brass spherical valves, incorporating chrome plated brass balls, butterfly type operating members and a drain off spigot connection that incorporates a rising spindle type headwork. For above ground use only. Maximum operating pressure 16 bar. Maximum operating temperature 85°C
Range of hand wheel operated or key operated gate valves with blue epoxy coated ductile iron bodies, ductile iron wedge encapsulated in EPDM. Models HY-002A & HY-002B incorporate brass valve seats Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
STAD range of balancing valves with brass bodies, PTFE sliding washer and EPDM O-rings. Models are available with or without a drain port. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of regulating valves, consisting of a brass body with thermostatic control elements and manually adjustable flow control valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'Celcon M90DW CF2001 Natural'. Natual (appears white), injection moulded POM material. For use with water up to 85°C.
'Purtop 1000 N'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS '7506-3-2024'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NMSP2104 M'. Factory applied, blue coloured, porcelain (vitreous) enamel coatings. Apply as per manufacturer’s user manual ‘specification no. PIN-10’, revision no. '0' dated '15/10/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431’ primer for use with ‘HYDRALFUN AC NOIR PAM -CZL8579’ finish/topcoat. Factory applied, black coloured (once mixed and applied), two-part epoxy primer for use with acrylic coating. Mix base & hardener of primer in a 100:10 weight ratio and apply one coat as per manufacturers TDS ‘NATZINC EP9010 BI 5431’, dated ‘February 2024’. No cure required. Apply one coat of the topcoat as per manufacturers TDS ‘HYDRALFUN AC NOIR PAM CZL8579’, dated ‘July 2018’ and cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SUPERPOXY 5000RP'. Factory applied, two component, blue coloured epoxy coating. Mix Parts A & B in a volume ratio of 3:1 and apply as per manufacturer's instructions issue reference 'SPI 20170413 ' dated September 1st, 2016. Cure for 58 hours@24°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaguard CSF 585/Blue'. Factory applied, blue coloured, two-component, solvent-free epoxy coating. Mix parts A & B in a volume ratio of 77.5:22.5 and apply as per manufacturer's Product Data Sheet '7785', dated 'August 19, 2022'. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSAW-JAL'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSAW-JAL (OPC-JKL)'. Factory applied, grey coloured ordinary portland cement. Mix cement, sand & water in a 1:1.5:0.5 weight ratio and apply as per work instructions 'JSAW/SMG/DISP/PRO/WI-11', version '3.3', effective date '15.04.2024'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KUBOTA Moderate Heat Portland Cement'. Factory applied, grey coloured Portland Cement. Mix sand:cement;water in a 2.4:1.0:0.4 weight ratio and apply as per manufacturer's instructions 'KBT20250107', dated '7th January 2025'. Cure for 6 hours @40°C followed by 18 hours @20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BELPA CSA 50'. Light green coloured, NBR/fibre gasket material manufactured by calendaring. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'GRE -FPI-KSA-WAVISTRONG1'. Green-brown coloured GRE pipe manufactured by helical winding. For use with water up to 85°C.
‘DENYL 6 5010 NERO 0300, DENYL 6 3010 NERO 0300, DENYL 6 1510 NERO 0300, DENYL 6 5010 NERO, DENYL 6 3010 NERO & DENYL 6 1510 NERO’. Black coloured, injection moulded, glass fibre filled PA6 materials. For use with water up to 85°C.
'Grilon TSG-30/4 FA Black 9840'. Black coloured, injection moulded PA material. For use with water up to 85°C.
Page 288 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
