UV disinfection unit with stainless steel body. Maximum working pressure 9.0 bar. Maximum operating temperature 55°C.
'Loctite PC 7255 GN (Green) coating for use with Bonderite M-NT 1455-W primer'. Factory applied, green coloured, two-component epoxy resin coating. In June 2025 ‘LOCTITE PC 7255 GY (Grey) coating for use with BONDERITE M-NT 1455 Primer-W Coating’ was added to the approval. Factory applied, grey coloured, two-component epoxy resin coating. Prime the surface to be coated with the Bonderite primer wipe. Mix and apply as per manufacturer’s TDS dated October 2016. Cure for 7 days@23°C at 45% relative humidity. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HY/NG' dated '2023-06-02'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PM6/35/7623 Vitreous Enamel Coating. Factory applied, blue coloured enamel coating. Apply and fire as per manufacturer's datasheet dated '01-2018' For use with water up to 85°C.
'18521 Kanepox Lining Free Blue for use with Kanepox Hardener 0362'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix 18521 Kanepox Lining Free Blue & Kanepox Hardener 0362 in a 3.5:1 volume ratio and apply as per manufacturer's datasheet ‘Rev. No. 11’ dated February 2018. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe IL 6001-120S'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS dated 22nd August 2018. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Strongcoat EPW-P'. Site applied, two-component, light grey coloured (once applied) epoxy coating. Mix Part A (light grey coloured liquid) with Part B (orange coloured liquid) in a 8.1:3.78 volume ratio and apply coat 1 as per manufacturer's TDS 06-0020-A-2021. Cure for 24 hours@23°C. Mix and apply coat 2 in the same way as coat 1 and cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DESCAFLEX PWH-300 601701, 601568 & 601700'. Range of black coloured, extruded polyethylene cables consisting of an outer sheath (available in two different thicknesses) and three or four inner cables. For use with water up to 85°C.
'LUBKOTE® E352, LUBKOTE® SG96(N96), LUBKOTE® SG98(N98)'. White coloured lubricants. Apply as per manufacturer's product data sheet 'YC20231201-1'. For use with water up to 85°C.
Range of wedge shoes (part numbers 2005036, 2006536, 2008036, 2010036, 2012536, 2015036, 2020036, 2025036, 2030036, 2040036, 2650036, 2660036, 40005036, 40006536, 40008036, 40010036, 40015036, 40020036, 40025036, 2680036 & 126100036). Black coloured, injection moulded nylon wedge shoes. For use with water up to 50°C.
Injection moulded, glass fibre filled nylon materials. For use with water up to 85°C. LCPA-G(1)06 HMBK001 (black coloured). LCPA-G(1)06 HMNC011 (natural, appears off-white). PA66-G(1)BK011 (black coloured). PA66-G(1)NC011 (natural, appears off-white). (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% (05) - 65%.
'Ultradur® B4300 G6 FC Aqua Uncolored'. Uncoloured (appears cream), injection moulded PBT material. For use with water up to 85°C.
‘LWF LTD FIBRE™MESSENGER PIPE 10/6’. Black coloured, extruded, flexible HDPE pipe. For use with water up to 23°C.
'Cool-FIT 4.0 & 2.0 Pipes'. Triple layered, extruded polyethylene pipe which comprises of a black coloured inner layer, off-white coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'Cool-FIT 4.0 & 2.0 Fittings'. Triple layered, injection moulded electrofusion fittings which comprise of black coloured inner layer, ivory coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'TORELINA A670R63N2 & TORELINA A670R63B2'. Natural (appears cream) and black coloured, injection moulded PPS materials (manufactured in Japan). For use with water up to 85°C.
`TORELINA A604WR G & TORELINA A604WR B'. Grey coloured and black coloured, injection moulded PPS materials (manufactured in Japan). For use with water up to 85°C.
‘TORELINA™ A604WR & TORELINA™ A604WR B’. Natural (appears beige) and black coloured, injection moulded PPS materials (manufactured in China). For use with water up to 85°C
'EC PP R-HC600TF nature. Natural (appears white), injection moulded polypropylene material. For use with water up to 85°C.
'SP-402M'. Black coloured, compression moulded natural rubber material. Shore hardness 78. Tested in-radius size 1.0mm. For use with water up to 60°C.
Page 278 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
