'Hepworth HDPE PE 100 Pipe (black) & HDPE PE 100 Pipe (black with blue stripes)'. Extruded polyethylene pipes. For use with water up to 60°C.
'Yuhong PP-R Pipe GS'. Green coloured (with two, red lines) PP-R pipe manufactured by single screw extrusion. For use with water up to 70°C.
‘Estane® Grades 58887 Nat 036, 58315 Nat 033, 58300 Nat 036, 58887 Nat 029, 58315 Nat 055, 58887 Nat 038 & 58887 Nat 055’. Natural (transparent, colourless), injection moulded TPU materials. For use with water up to 23°C.
'INOFLAR™ 1005, INOFLAR™ 1011, INOFLAR™ 1020 & INOFLAR™ 1125'. Off-white coloured, injection moulded PVDF materials. For use with water up to 85°C.
‘Sikadur 31 DW Rapid for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW Rapid’ in a 3:1 weight ratio and apply as per product data sheet ‘March 2021, Version 01.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur 31 DW for use with Combiflex TF Tape’. Site applied, grey coloured two-component epoxy resin for use with grey coloured TPE Tape. Mix parts A & B of ‘Sikadur 31 DW’ in a 3:1 weight ratio and apply as per product data sheet ‘February 2022, Version 03.03’. Immediately apply ‘Combiflex TF Tape’ as per product data sheet ‘May 2021, Version 01.01’ and cure for 7 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TIMO 4-80 ‘O’ rings and washers'. Black coloured, injection moulded EPDM ‘O’ rings and washers. Shore hardness 80. The ‘O’ rings have an in-radius size of between 0.52mm & 2.67mm. The washers have an in-radius size of between 0.52mm & 2.71mm. For use with water up to 85°C.
'TIMO 7-70 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
'EPDM 70.503-00 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'EPDM H 85'. Black coloured, compression moulded EPDM rubber material. Shore hardness 85. Tested in-radius size 1.10mm. For use with water up to 70°C.
'Mescola EPDM-PX 659/70.nr'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'0477 NBR 70' components. Black coloured, injection moulded NBR rubber ‘O’ rings, washers and lip seals. Shore hardness 70. The ‘O’ rings have an in-radius of 1.31mm, the washers 1.05mm and the lip seals 0.45mm. For use with water up to 60°C.
'Akfix PS253 Pipe Sealant Medium Strength'. Blue coloured pipe sealant. Apply as per manufacturer's TDS 'Rev.01', issue date '23/10/2019'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hinton Thread Sealant HTS50 & HTS250'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions dated '2023-06-07', 'review 6' and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Hinton Solvent Cement HSC125 & HSC250'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 02062023'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by electronic or manual actuation. Maximum working pressure 10.0 bar. Cold water use only
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Three-hole, single outlet (fixed), combination tap assembly (brass body – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to the shower outlet. The product is supplied with a stainless-steel braided EPDM lined flexible connection hose to connect the head work to the spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted, three-hole, single outlet, fixed combination tap assembly (chrome plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The product is supplied with a shower handset holder that incorporates a manual diverter and a cascade type spout outlet. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 278 of 584
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
