'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Carboguard AQP FC Part A and Part B'. Site applied, grey coloured (once applied) epoxy coating. Mix Parts A & B in a weight ratio of 1:1 and apply as per manufacturer's Product Data Sheet '8163', dated 'March 2025'. Cure Coat 1 for 24 hours at 20°C and Coat 2 for 7 days at 20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monoflex W'. Grey coloured, extruded TPO 'tape'. Shore hardness 91. Tested in-radius size between 0.45mm & 1.0mm. For use with water up to 70°C.
'7740 WPG'. White coloured, silicone based lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'RPL-104'. Off-white coloured, unsaturated polyester resin material, manufactured by hand lay up process. For use with water up to 23°C.
'R579 TP13582 BLACK & R579 TP14619 BLACK'. Black coloured, rotomoulded PE materials. For use with water up to 85°C.
'Fortron® 1130T4 SD3039 Black'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Hostalen PP H2142 12'. Black coloured, injection moulded and compression moulded polypropylene material. For use with water up to 23°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
‘E4028WCC, E4510WCC, E5076WCC, E5522WCC, E6020WCC, E6020, E6541WCC, E7091WCC, E7091, E7528WCC, E8027WCC, E8506WCC & E9011WCC ‘O’ rings’. Black coloured, compression moulded EPDM ‘O’ rings. Shore hardness between 40 & 90. Tested in-radius size between 0.5mm & 3.5mm. ‘E4028WCC Gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 40. Tested in-radius size 0.8mm. For use with water up to 85°C.
'LOCTITE® 577™ & LOCTITE® SF 7649 Activator'. Yellow coloured thread sealant for use with light green coloured activator. Apply LOCTITE® 577™ as per manufacturer's technical data sheet reference ‘0.0’, dated November 2024 and LOCTITE® SF 7649 Activator as per manufacturer's technical data sheet reference ‘1.4’, dated June 2014. For use with water up to 23°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'Benvic IR745AB/9738' & 'IR712AB/9738'. Grey coloured (opaque), compression moulded PVC materials. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). The flow is controlled via a solenoid valve, activated via an infra-red sensor and temperature controlled via manual lever. The inlets incorporate single check valves cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are supplied with a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
WC Cistern incorporating a side or bottom entry float operated inlet valve and a dual flush Drop Valve (Acclaim V) or Syphon (Acclaim S) of full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern can be operated by lever or manual push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| FLKIT40 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT60 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
| FLKIT80 C | Chrome | 1/2" BSP | Open Outlet bar | 60 °C | Bristan | Handset | No | Not applicable | Not Applicable | Not Applicable | Flow Regulator Fitted, Shower Hose, Handset, Riser Rail, |
Spring loaded, resilient trim, in-line check valve cartridges with plastic guide, stem and body. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Spring loaded resilient trim check valve cartridge with plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floguard range of in-line non-verifiable double check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a DZR brass body (FLOW230002 model is nickel plated). Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 Bar Maximum operating temperature: 65°C
Page 272 of 310
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
