'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ODSi-PUMP111'. White coloured silicone grease. For use with water up to 85°C.
'ODSi-PUMP227'. White coloured fluorinated polymer grease. For use with water up to 85°C.
'Vitamide AR86BK 1727/2 MAL'. Black coloured, injection moulded glass filled, PA66 material. For use with water up to 85°C.
'Almona PE Electrofusion Fitting'. Black coloured, injection moulded polyethylene electrofusion fitting. For use with water up to 85°C.
'UPMC PPR Pipe'. Green coloured (with yellow stripe), extruded PPR pipe. For use with water up to 85°C.
'Techno PP-RCT Pipe'. Green coloured (with yellow stripe), extruded PP-RCT pipe. For use with water up to 85°C.
'Techno UV Black Fitting'. Black coloured, injection moulded PPR fitting. For use with water up to 85°C.
'Techno UV Black Pipe'. Black coloured (with yellow stripe), extruded PPR pipe. For use with water up to 85°C.
'Almona PP-RCT 5 layered pipe' & 'Almona PP-RCT 3 layered pipe'. Extruded, multi-layered PP-RCT pipes. Both pipes have a green inner layer, grey second layer and green third layer. The 5-layer pipes then have an additional grey fourth layer and black outer layer. For use with water up to 85°C.
'Apitherm PP-RCT Class 2 & Class 5 Pipes'. Green coloured (the Class 5 pipes have a red stripe), extruded PP-RCT pipes. For use with water up to 85°C.
'Apitherm PP-RCT Class 2 & Class 5 Fittings'. Green coloured, injection moulded PP-RCT fittings. For use with water up to 85°C.
'Ultrason® S 2010 G4'. Light beige coloured, injection moulded polysulphone material. For use with water up to 85°C
'662016, 662014, 662062 & 662061'. White coloured, PTFE tape manufactured by calendering. For use with water up to 85°C.
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'TIMO 3-70 'O' rings and gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size between 0.50mm & 2.67mm. For use with water up to 85°C.
Page 264 of 390
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
