'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per manufacturer's Technical Data Sheet 'TWJ-H-453', 'Edition A1', dated '01/12/2023'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal Liquid Epoxy Paint'. Factory applied, two-component epoxy paint available in red/brown, grey, blue & white colours. Mix base and activator in a volume ratio of 3:1 and apply as per manufacturer's instructions 'DI/FG/2024/056', dated '25/04/2024'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', issue '04', rev. '0', dated '22.08.2024'. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'POLYPOL-1023'. Beige coloured GRP rein manufactured by hand lamination. For use with water up to 65°C.
'VYDYNE AG7K-1001'. Light grey coloured, injection moulded PA66 material. For use with water up to 70°C.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'PC IR2200, Housing'. Clear (transparent), injection moulded polycarbonate housing component. For use with water up to 65°C.
'UPI Injection Molded Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'STAR Spigot Fittings'. Black coloured, extruded PE100 fitting. For use with water up to 60°C.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'TORELINA® A670MWR1B'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'AquaTerra SDR 6 PP-R Pipes'. Green coloured, extruded PP-R pipes. 'AquaTerra SDR 7.4 PP-R Pipes', green coloured, extruded PP-R pipes were added to the approval in September 2024. All pipes are or use with water up to 85°C.
'KALSON PP Saddle Fittings'. Blue coloured, injection moulded polypropylene saddle fittings. For use with water up to 65°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'OLDAL 460'. Black coloured, injection moulded EPDM material. Shore hardness 50. Tested in-radius size 1.2mm. For use with water up to 85°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
Page 257 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
