'Powertherm PP-R pipe'. Green coloured, extruded PP-R pipe (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'POWERtherm PP-R Fittings'. Green coloured, injection moulded PP-R fittings (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'9710-ALT 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size between 1.0mm & 2.0mm. For use with water up to 23°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
'Griffon Silpat'. Grey coloured jointing compound. Apply as per manufacturer's instructions '7001669', issue '1'. For use with water up to 85°C.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Page 253 of 408
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
