Range of resilient seated gate valves with ductile iron bodies and bonnets (blue epoxy powder coated) with a ductile iron wedge encapsulated in EPDM. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating blue epoxy coated ductile iron body and EPDM gasket. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Talbot range of gunmetal screw down stop valves for use with MDPE PE80 pipe (manufactured to EN12201). The products are supplied with loose (blue plastic) pipe inserts. Maximum working pressure 16.0 bar. Cold water use only.
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitors with chromium plated copper bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 35°C
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Ionisation system with stainless steel body and copper & silver electrodes. Maximum working pressure 12.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
'CRPM 1002 Clinching Ring'. White coloured, injection moulded acetal component. For use with water up to 23°C.
'Kepital F10-01 T2, F10-02, F10-03H, F20-03M, F25-03 & F30-03M'. The following grades were added to the approval in April 2023: ‘Kepital F30-34, F10-01, F10-03HM, F20-03, F25-03M & F30-03’. Natural, unpigmented (white in appearance), injection moulded POM materials. All the grades listed can be coloured using the following masterbatch MB-S315F (black coloured masterbatch). All are for use with water up to 85°C.
'Kersic 1000'. Grey coloured, compression moulded silicon carbide ring. For use with water up to 85°C.
'221K'. Beige coloured, compression moulded ceramic washer. For use with water up to 85°C.
'TEPICOMPOWDER PC-200F U'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur Multi-Strength 35531 Grey'. Factory applied, grey two-component epoxy coating. Mix base and curing agent in a 3:1 volume ratio and apply in accordance with manufacturer's Product Data Sheet issued July 2022. Cure for 7 days@20°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur Multi-Strength 35531 Red'. Factory applied, red two-component epoxy coating. Mix base and curing agent in a 3:1 volume ratio and apply in accordance with manufacturer's Product Data Sheet issued July 2022. Cure for 7 days@20°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maxline 100 Potable Water Coating Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDSMLI100.rv5.04042023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Page 224 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
