'SATHAVAHANA Ordinary Portland Cement'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Sulphate Resistant Portland Cement'. Factory applied, grey coloured Sulphate Resistant Portland Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SATHAVAHANA Portland Slag Cement'. Factory applied, grey coloured Portland Slag Cement. Mix cement, sand & water in a mass ratio of 1:1.5:0.5. Apply as per work instructions 'JSAW/AP01/DISP/PRO/WI-09', version '1.0', effective date '01.12.2022'. Cure for 3 hours at 45°C & 90% humidity. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RMD 7080/xx, RUD 2230/xx, RMD 7100/xx, RUD 2247/xx, RUD 2273/xx, RMD 7061/xx'. 'xx' denotes the customer and can be replaced with numbers between 01 & 99. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions '0703231010' dated 14.03.23. Cure for 10 minutes@860°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
ML-9005WGL414 (black coloured - RAL 9005), ML-6018WGL424 (green coloured - RAL 6018), ML-9A10WGL444 (white coloured - RAL 9010), ML-5007WGL424 (blue coloured - RAL 5007) & ML-6621WGL424 (green coloured - Pantone 334 C). Factory applied, electro-statically sprayed epoxy powder coatings. Apply as per manufacturer’s Product Data Sheet ‘Pdb_ML-WGL414-EN (03-2023)’, dated ’23.03.2023’. Stove (cure) for 8 minutes at 180°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ILPEA 70-90 EPDM HOSE WRAS AF'. Black coloured, extruded EPDM hose. Shore hardness 80. Tested in-radius size 1.3mm. For use with water up to 23°C.
'P901BK'. Black coloured, extruded HDPE material. For use with water up to 23°C.
Page 208 of 401
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
