Directory Search Results

Print List

#2306096

Range of single and dual flush WC outlet valves. The valves incorporate an internal overflow and are operated with one push button (single flush) or two push buttons (dual flush). Cold water use only.

Section:
1305 Flushing Mechanisms
Section Subtitle:
WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.
WRAS Approval Number:
2306096
Size:
10.1283 - 1 1/2" or 2" BSP (M).
Marking:
Plumb Bliss & PB logo on body
Installation Requirements:
R001 R571 R581
Expiry date:
30/06/2028
Model:
10.1283 Dual Flush Valve

Approval Holder:
Bliss UK Group Ltd
Company Name
Bliss UK Group Ltd
Address
Unit 4A Kinsbourne Farm Wick End Stagsden Bedfordshire
Postcode
MK43 8TS
Country
United Kingdom
Phone
01234 860230
General Email
accounts@blissukgroup.co.uk

View All Listings by this Company

Print This Approval


#250502703

‘Zip Aquapoint IV’ range of wall mounted directly heated unvented storage vessels (cased and insulated) incorporating an enamel lined cylinder and safety kit. The cylinder is factory fitted with a temperature and pressure relief valve (7.0 bar/90°C) and a drain valve. The product is supplied with an installation kit comprising of an expansion vessel, tundish and an inlet manifold incorporating a 6.0 bar expansion relief valve, an adjustable pressure reducing valve with stainless-steel strainer (adjustable between 2.7 and 3.3 bar, but pre-set at 3.0 bar), and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The compression connections of the installation kit are for use with copper pipe (Manufactured to EN 1057). Maximum working pressure 5.5 bar. Maximum operating temperature 70°C. Cold supply only.

Section:
1380 Heaters
Section Subtitle:
Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.
WRAS Approval Number:
250502703
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
Aquapoint iV models: ½” BSP (M) inlet and outlets. AQ105 and AQ0108 Installation kits: 22mm compression.
Marking:
Zip on front panel. Zip company logo, model, capacity and other technical information on adhesive label on cylinder body casing.
Installation Requirements:
R001 R511
Expiry date:
31/05/2030
Model:
AP430S - 30 Ltr Direct, AP450S - 50 Ltr Direct, AP480S - 80 Ltr Direct, AP4100S - 100 Ltr Direct. All products are supplied with an installation kit, either AQ105 (AP430S and 450S models) or AQ108 (AP480S and AP4100S models).
Product Images

Approval Holder:
Zip Heaters UK Ltd T/A Zip Water UK
Company Name
Zip Heaters UK Ltd T/A Zip Water UK
Address
Trafalgar House, Trafalgar Business Park, Dereham
Postcode
NR19 1JG
Country
United Kingdom
Phone
0345 600 5005
General Email
sebastian.ducker@zipwater.co.uk

View All Listings by this Company

Print This Approval


#250504712

Range of counter-top or under-sink electrical water heaters. Maximum working pressure 6.5 bar. Maximum operating temperature 75°C, except 65°C for 10L models.

Section:
1390 Heaters
Section Subtitle:
Electric, thermal storage, mains fed, open outlet.
WRAS Approval Number:
250504712
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
1/2” BSP (M)
Marking:
Midea logo on body. Midea logo, Capacity, Model No.,Pressure, Other tech info on data label on body
Installation Requirements:
R001
Expiry date:
31/05/2030
Model:
Da-bcd a = Volume (available in 10, 15 & 30), b = Rated power (available in 20 & 30, 20 stands for 2kW, 30 for 3kW), c = Cover type (available in VD, VD2 & VD3), d = Installation position (available in O & U, O stands for over sink, U stands for under sink) Where a typical code is: ①D10-20VDO: 10 = volume (L) 20 = rated power (2kW) VD = the type of cover O = over sink range ②D30-30VD3U: 30 = volume (L) 30 = rated power (3kW) VD3 = the type of cover U = under sink range
Product Images

Approval Holder:
Wuhu Midea Kitchen & Bath Appliances Manufacturing Co., Ltd.
Company Name
Wuhu Midea Kitchen & Bath Appliances Manufacturing Co., Ltd.
Address
Wanchun East Road Economic and Technological Development Zone Wuhu City Anhui Province
Country
China

View All Listings by this Company

Print This Approval


#2103043

Range of rotating piston, volumetric in-line water meters with brass bodies. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1505 Water Meters
Size:
¾” BSP - 2” BSP (M) inlet and outlet.
Marking:
George Kent logo on lid. GKMV30, serial number, size, pressure and technical information on body housing rim.
Installation Requirements:
R001
Expiry date:
31/03/2026
Model:
GKMV30 - DN15, 20, 25, 30 & 40

Approval Holder:
George Kent (Vietnam) Co Ltd
Company Name
George Kent (Vietnam) Co Ltd
Address
F3-6 (Area A), Lot A4, NA1 Street Thoi Hoa Industrial Park, Thoi Hoa Ward, Ben Cat City Binh Duong Province
Country
Vietnam
Phone
+84 274 3803 167
General Email
lhpan@georgekent.net

View All Listings by this Company

Print This Approval


#2305096

GKMV30P range in-line volumetric water meters with black plastic bodies. Maximum working pressure 16.0 bar. Cold water use only.

Section:
1505 Water Meters
Size:
See model.
Marking:
GKM branded logo on lid. Flow direction arrow, Meter type (GKMV30P) & additional information on Chamber Housing.
Installation Requirements:
R001
Expiry date:
31/05/2028
Model:
GKMV30P Range: DN15: ¾" BSP (M) inlet and outlet, DN20: 1" BSP (M) inlet and outlet, DN25: 1¼" BSP (M) inlet and outlet.

Approval Holder:
George Kent (Vietnam) Co Ltd
Company Name
George Kent (Vietnam) Co Ltd
Address
F3-6 (Area A), Lot A4, NA1 Street Thoi Hoa Industrial Park, Thoi Hoa Ward, Ben Cat City Binh Duong Province
Country
Vietnam
Phone
+84 274 3803 167
General Email
lhpan@georgekent.net

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 2039 of 2345

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.