Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves operate via non-rising spindle headwork. Maximum working pressure 16.0 bar and a maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass or DZR brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising shaft with a gear box operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves incorporating a brass body and a brass disc. The valves operate via non-rising spindle headwork with a hand wheel operating member Maximum working pressure 16.0 bar.
Range of gates valve with ductile iron bodies (blue epoxy coating), EPDM seats and `O` rings. The valves are handwheel operated via a non-rising spindle. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of stop valves with bronze bodies and bonnets. Rising spindle. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Electrolytic scale inhibitors with nickel plated copper bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 70°C
Electrolytic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
McAlpine Scale Defender Limescale Inhibitor’. The product does not incorporate any backflow protection.. Maximum working pressure 10.0 bar. Cold water use only.
Ultra-violet disinfection unit comprising of a stainless-steel body and quartz sleeve. Maximum working pressure 8.0 bar. Cold water use only.
'Support Ring F1'. White coloured, injection moulded acetal support ring. For use with water up to 85°C.
'YT425'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'AYYT01' dated '2023.3.16'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Polywarm'. Factory applied, brown coloured enamel powder coating. Apply as per manufacturer's instructions '1024'. Cure for 20 minutes@240°C. For use with water up to 85°C.
'Interpon HYF PLUS HJ701I'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's product datasheet 'Ed.3 – October 2014' and stove/cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Acothane DW Cream, Acothane DW Blue & Acothane DW Grey’ site applied, two-part polyurethane coatings to be used with or without ‘Acothane LV’ polyurethane sealer. ‘Acothane LV’ (base coat) and ‘Acothane DW Cream’ (base or middle coat) are approved for use as non-water contact coats. ‘Acothane DW Blue & Acothane DW Grey’ are approved as water-contact coats and may be used alone or as the water contact coat in any of the following combinations: Acothane DW LV Sealer/ Acothane DW Cream/ Acothane DW Blue. Acothane DW LV Sealer/ Acothane DW Cream/ Acothane DW Grey. Acothane DW Cream/ Acothane DW Blue. Acothane DW Cream/ Acothane DW Grey. Mix Part A & Part B of Acothane LV in a weight ratio of 100:48, apply as per TDS dated March 2022 and then cure for 4 hours@3°C before applying cream coating. Mix Part A & Part B of Acothane DW Cream in a weight ratio of 100:31, apply as per TDS ‘06ADW’, issue ‘2’, dated December 2022 and then cure for 4 hours@3°C before applying blue or grey water contact coat. Mix Part A & Part B of Acothane DW Blue/Grey in a weight ratio of 100:31, apply as per TDS ‘06ADW’, issue ‘2’, dated December 2022 and then cure for 7 days@3°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LZFRP-GP-01'. Green coloured GRP material manufactured by filament winding. For use with water up to 85°C.
'SIL70W01 hoses'. White coloured (translucent), extruded silicone hoses with a shore hardness of 70. Tested in-radius sizes between 0.25 and 2.0mm. For use with water up to 85°C.
'Rotormagnet 12-0000294'. Dark grey coloured, injection moulded Polyamide + Strontium Ferrite magnet. For use with water up to 60°C.
Page 200 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
