Range of drinking water stations. Flow is controlled via a push-button tap assembly (which incorporates a flow regulator) on all models. Model Park Tap 016 0104-TS-016_WRAS incorporates two outlets (bubbler at low-level & bottle filler at high-level). The flexible hose assembly which rises through the body of the station to the lower outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Model Hall TAP_EN (indoor) incorporates one (bottle filler type) outlet with a fixed drip tray under. Street Tap 0104-TS003_WRAS incorporates one (bottle filler type) outlet. The flexible hose assembly which rises through the body of the station to the outlet incorporates a single check valve assembly (verified by test as suitable for backflow protection against Fluid Category 2). Maximum working pressure 3.5 bar. Cold water use only.
'Bottom Plate K3'. Off-white (opaque) coloured, injection moulded POM component. For use with water up to 65°C.
'T195 NS sealing plate'. White coloured, compression moulded sealing plate. For use with water up to 85°C.
'T11 Sealing Ring'. Black coloured, compression moulded, ceramic sealing ring. For use with water up to 85°C.
'CEC-GFS Enamel, Black Blue RAL5004'. Factory applied, blue/black (appears black) coloured, enamel coating. Apply as per manufacturer's instructions 'ZZ-Ins001', dated '2021.01.01'. GFS-G base glaze: dry for 15 Minutes at 200°C then fire for 12 minutes at 870ºC. GFS-S surface glaze: dry for 15 Minutes at 200°C then fire for 10 minutes at 830ºC. For use with water up to 85°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 480 FC'. Site applied, red coloured (once mixed), two part epoxy coating consisting of a resin and hardener. Mix, apply and cure (fully dry) in accordance with manufacturer's technical data sheet dated 23/09/2021. For use with water up to 23°C.
'420 OE UHMWPE'. Multi-layered (7 layers), Ultra High Molecular Weight Polyethylene hose manufactured by wrapping on a mandrel. The inner layer is white coloured polyethylene, and the outer layer is blue coloured rubber. For use with water up to 23°C.
'509 OE/UHMWPE' hose, manufactured by mandrel wrapping and vulcanisation. Multi-layered hose comprising of a clear PE inner layer, blue coloured EPDM second layer, white coloured reinforcement third layer, blue coloured EPDM fourth layer, grey coloured helix wire fifth layer and blue coloured EPDM outer layer. For use with water up to 23°C.
'Hydro 90'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'June 2022'. For use with water up to 85°C.
'Sinopec Drinking Water Pipeline Sealing Lubricant (Product Code: 523478)'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Brett Martin B9333 & B9444'. Blue coloured lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'IRRIPLASTEC PE 100 WATER'. Dual layered, extruded pipe comprising of a white coloured (opaque), PE inner layer and a black coloured, PE outer layer. For use with water up to 23°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Pipes'. Black coloured (with dark blue stripe), extruded HDPE pipe. For use with water up to 60°C.
'DR-PLAST HDPE PE-100 Fittings'. Black coloured, HDPE fittings manufactured by either injection moulding or butt fusion welding. For use with water up to 60°C.
'PPHS40'. Pale grey coloured, injection moulded PP material. For use with water up to 23°C.
'Aquatherm Green' range of extruded, polypropylene pipes, for use with water up to 85°C. (1) Aquatherm Green Pipe. Single layered, green coloured polypropylene pipe. The SDR11S pipe has four, blue longitudinal stripes on the exterior of the pipe. (2) Aquatherm Green Pipe (formerly named Fusiotherm Fibre Composite Pipe). Triple layered pipe consisting of a light green coloured polypropylene inner layer, glass fibre reinforced, polypropylene middle layer and light green coloured polypropylene outer layer. The pipe has dark green stripes on the exterior of the pipe.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'CE EPDM (TY-02-50) & CE EPDM (TY-05-80)'. Black coloured, compression moulded EPDM sheet materials. Shore hardness between 50 & 80. Tested in-radius size between 0.75mm & 1.0mm. For use with water up to 23°C. From February 2024 the materials are for use with water up to 65°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
Page 20 of 48
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
