'KUBOTAPOWDER TK1413F M'. Factory applied, grey coloured epoxy resin powder coating. Apply as per manufacturer's Technical Information 'No. SG23180' dated '11 June 2021'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELEC GRP PIPE B'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'SHUANGSHI GRP PIPE 51160'. Yellow coloured GRP pipe manufactured by filament winding. For use with water up to 60°C.
'SYL-8668'. White coloured (opaque) grease. For use with water up to 70°C.
'G. BESLUX BESSIL 6001'. White coloured, opaque silicone grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Denyl 66 3010 Natural F' & 'Denyl 66 3010 Black F'. Natural (appears off-white) and black coloured, injection moulded, Polyamide 66 materials. For use with water up to 65°C.
'Jingtong HDPE Pipe'. Black coloured (with blue external lines), extruded HDPE pipes. For use with water up to 65°C.
'Jingtong HDPE Fitting'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'Jain HDPE (PE 100) Blue Fittings). Blue coloured HDPE fittings manufactured by injection moulding or extrusion. For use with water up to 65°C.
'TEGA PE100 fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Stars Water Tank Panel'. Multi-layered, roto-moulded LLDPE/PE foam panel comprising of a white (opaque) water contact layer, off-white (translucent) second layer, black (opaque) third layer and white (opaque) outer layer. For use with water up to 65°C.
'DERINSU PE100 Fitting'. Black coloured, injection moulded PE100 fitting. For use with water up to 60°C.
'Wefatherm Fitting'. Green coloured, injection moulded PP-R fitting. For use with water up to 60°C.
'Wefatherm Pipe'. Green coloured (with or without blue external stripe), extruded PP-R pipe. 'Wefatherm Fibre Pipe'. Extruded, multi-layered pipe comprising of a green coloured PP-R inner layer, green coloured PP-R/fibre middle layer and green coloured (with red stripe) PP-R outer layer. Both pipes are for use with water up to 60°C.
'Aquatherm Fitting'. Green coloured, injection moulded polypropylene fittings. For use with water up to 60°C.
'Borealis HB601WG'. Clear, injection moulded polypropylene material. For use with water up to 85°C.
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
‘3M™ Dyneon™ Fluoroplastic ET 6235Z’. Natural (translucent, white coloured), compression moulded ETFE material. For use with water up to 85°C
Page 182 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
