Press-Inox range of stainless-steel crimped fittings (‘M’ crimp profile) for use with stainless steel pipe (manufactured to EN10204). For above ground use only. Maximum working pressure: 16Bar. Maximum operating temperature: 100°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241102057

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm - 168.3mm (excluding 28mm). (Including 28mm from December 2024).

Marking:

PCC Logo, PI 316L, Size, Year of manufacture (YY-MM) and DVGW on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

All Models sizes are in mm are Pressfit unless specified are BSP 12000 Straight Coupling 15mm - 168,3mm 12010 Straight Male Adapter 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 66.7 x 2 1/2" 76.1 x 2 1/2" 88.9 x 3" 108 x 4" 12020 Straight Female Adapter 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 12040 Sleeve Coupling 15mm – 108mm 12070 Tap Connector 15 x 3/4" 18 x 3/4" 22 x 1" 35 x 1 1/2"12080 Male Union 15 x 1/2" 18 x 1/2" 22 x 3/4" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 12100 Equal Tee 15mm - 168,3mm 12110 Reduced Tee 15mm - 168,3mm 12120 Female Tee 15mm – 108mm 12200 Bend 90° 15mm - 168,3mm 12210 Streetbend 90° 15mm - 168,3mm 12230 Bend 45° 15mm - 168,3mm 12240 Streetbend 45° 15mm - 168,3mm 1231 Male Threaded Bend 90° 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 1232 Female Threaded Bend 90° 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 1234 Female Wallplate 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 12350 Male Bend 90° 15mm – 54mm 12360 Crossover / By-Pass Bend 15mm – 54mm 12400 Flange PN16 with pressend 22 x 1/2" 22 x 3/4" 22 x DN20 35 x DN32 42 x DN40 54 x DN50 66.7 x DN65 76.1 x DN65 76.1 x DN80 88.9 x DN80 108 x DN100 139.7 x DN125 168.3 x DN150 12410 Endcap 15mm – 108mm 12430 Male reducer 15mm - 168,3mm 12450 Insert Male Adapter 15mm – 54mm 12460 Insert Female Adapter 15mm – 54mm 12820 O-Ring 15mm - 168,3mm Models Added December 2024: 12010 Straight Male Adapter 28 x 3/4" 28 x 1" 12020 Straight Female Adapter 28 x 3/4" 28 x 1" 12070 Tap Connector 28 x 1 1/4" Male Union 28 x 1" 1231 Male Threaded Bend 90° 28 x 3/4" 28 x 1" 1232 Female Threaded Bend 90° 28 x 3/4" 28 x 1" 1234 Female Wallplate 28 x 3/4" 28 x 1" 12400 Flange PN16 with pressend 28 x 1" 28 x DN25

Product Images

Approval Holder:

PCC GmbH

Company Name

PCC GmbH

Address

Dusseldorfer Strasse 15, D-71332 Wailblingen

Country

Germany

View All Listings by this Company

Range of copper brazed, stainless steel heat exchangers. Available with between 4 – 70 plates (see models). Maximum working pressure: 16.0 bar. Maximum operating temperature: 99°C.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

see models

Marking:

SWEO and product info on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

E5T Number of plates minimum: 6 Number of plates maximum: 48 No connection type or ¾” BSP (M) E5AS Number of plates minimum: 4 Number of plates maximum: 40 No connection type or ¾” BSP (M) E5K Number of plates minimum: 8 Number of plates maximum: 40 No connection E6T Number of plates minimum: 4 Number of plates maximum: 40 No connection type, ½” or ¾” BSP (M) E8T Number of plates minimum: 4 Number of plates maximum: 40 No connection type, ½” or ¾” BSP (M) E8AS Number of plates minimum: 4 Number of plates maximum: 46 No connection type or ¾” BSP (M) E8LAS Number of plates minimum 10 Number of plates maximum: 70 No connection, ¾” or 1” BSP (M)

Product Images

Approval Holder:

SWEP International AB

Company Name

SWEP International AB

Address

Järvgatan 3B, Box 105, 26122 Landskrona

Country

Sweden

View All Listings by this Company

Range of indirect heat interface units (HIU) providing heating and instantaneous hot water. The central heating and hot water is generated via plate heat exchangers. Maximum operating pressure 10 bar (primary and DHW secondary). Maximum operating pressure 2.5 bar CH secondary Maximum operating temperature 90°C

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241104709

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression

Marking:

Bosch on front panel and technical info on adhesive label.

Installation Requirements:

R001 R140 R360

Expiry date:

30/11/2029

Model:

7-735-600-739 - Flow 8500 40, 7-735-600-740 - Flow 8500 40 H, 7-735-600-741 - Flow 8500 50, 7-735-600-742 - Flow 8500 50 H, 7-735-600-743 - Flow 8500 60, 7-735-600-744 - Flow 8500 60 H.

Product Images

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Range of water meters with brass bodies and EPDM ‘O’-rings and plastic strainer on inlet. Maximum working pressure 16 bar. Cold water use only.

Section:

1505 Water Meters

Size:

1 1/4” BSP (M) 1 ½” BSP (M) 2” BSP (M)

Marking:

Resideo & technical information on dial face. Flow arrow cast on body.

Installation Requirements:

R001

Expiry date:

30/09/2028

Model:

EW1100CC2800 EW1100CC3900 EW1100CC4600 EW1100CM2800 EW1100CM3900 EW1100CM4600 - DN25, DN32 and DN40

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Range of water meter manifolds with plastic bodies for use with PE80 pipe (manufactured to BS EN 12201). The inlets incorporate a spherical valve and a check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1510 Water Meter Manifolds

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

25mm & 32mm pushfit

Marking:

Atplas logo on body.

Installation Requirements:

R001 R008

Expiry date:

30/11/2029

Model:

MB57425DU Matrix. MB5743225DU Matrix. MB5743232DU Matrix. MB57432DU Matrix. MB5743225DDCV Matrix.

Product Images

Approval Holder:

Atlantic Plastics Ltd.

Company Name

Atlantic Plastics Ltd.

Address

Coytraherne Close, Brackla, Bridgend

Postcode

CF31 2AX

Country

United Kingdom

Phone

01656672628

General Email

rhodgkiss@atplas.co.uk

View All Listings by this Company