Range of commercial washing machines with flow controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The products are supplied with three ¾” x ¾” BSP (F) double check valve assemblies (suitable for backflow protection against Fluid Category 3) for installation on each inlet prior to a HDPE inlet hose with ¾” x ¾” captive nut end connections. Maximum working pressure 5.7 Bar. Maximum operating temperature 60°C.
Range of commercial dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 4.0 bar. Cold water use only.
Range of magnetic and electrolytic water conditioners with nickel plated copper bodies. Maximum working pressure 10 bar. MagnaScale2 model has a maximum operating temperature of 85°C. ElectroScale 2 models are for cold water use only.
'Electrocoat BP 116'. Factory applied, black coloured bitumen paint. Apply as per manufacturer's technical data sheet, document number 'ECL/TDS/BP116' dated 10th January 2016. Cure for 30 minutes@55°C and then 10 hours@23°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Karumel EX4412 Blue & Grey’. Factory applied, blue or grey coloured, epoxy resin based powder coating. Apply and cure as per manufacturer’s instructions reference 'PCA-21062901', issued August 2021. For use with water up to 85°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
`POWLAC EY161`. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions `no. CKP-2015-0172`. Cure for 5 minutes@180°C. For use with water up to 85°C. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S-006TG'. Cream coloured, compression moulded GRP panel. For use with water up to 23°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'IPF-GRP-H2O'. Off-white/beige coloured GRP/GRV pipe manufactured by filament winding. For use with water up to 60°C.
'XIN-6709-01 hose' manufactured from 'GR-PVC 001N' raw material. Single layered, extruded, black coloured PVC hose. For use with water up to 85°C.
'Ultradur® B4300 G6 HR FC Aqua grey 35413 '. Grey coloured, injection moulded PBT material. For use with water up to 65°C.
'Revolve 6402U'. White coloured (translucent), polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'Al Bassam High Density Polyethylene Underground Water Tank Panel'. Black coloured, blow moulded HDPE tank panel which is available with three or four layers (of the same material). For use with water up to 65°C.
'Al Bassam High Density Polyethylene Aboveground Water Tank Panel'. Blow moulded HDPE tank panel which comprises of four layers and has a black coloured water contact layer, red and black coloured inner layers and white coloured outer (non-water contact) layer. For use with water up to 65°C.
'BKBB-660'. Black coloured LLDPE 'buoyant body' manufactured by rotational moulding. For use with water up to 23°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Helisystem CT fitting'. Green coloured, injection moulded PP-RCT fitting. Between July 2021 and September 2022, the fitting was for use with water up to 23°C. Between October 2022 and July 2026, the fitting is for use with water up to 75°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
Page 18 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
