Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down valves with brass or DZR brass bodies, brass or DZR brass bonnets, EPDM washers and PTFE seats. Compression connection to be used with copper pipe manufactured to EN1057. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
‘ET Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/013', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Sulphate Resisting Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/014', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ET Blast Furnace Slag Cement’. Factory applied, grey coloured cement. Mix and apply as per manufacturer’s ‘Standard Operating Procedure 'ET-SAM/DIP-PP/SOP/012', 'Rev. No 01', dated '15.12.2019'. Cure for 40 days@26°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Promag’. Factory applied, black coloured PUR coating system comprising of a primer and topcoat. ‘Promag Primer’ is a two-part primer to be mixed in a 1:2 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 2 hours@23°C. ‘Promag Topcoat’ is a three-part topcoat to be mixed in a 92.59:5.19:2.22 mass ratio before applying as per manufacturer’s core instructions ‘TLB: 10000043811’, ‘Version: M’. Cure/dry for 20 seconds@20-26°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'571983 & 571984'. White coloured (semi-translucent), extruded PTFE tape. For use with water up to 85°C.
'ESTANE® 58197 Nat 022'. In August 2023 'ESTANE® 58197 NAT 01' was added to the approval. Natural (transparent, colourless), injection moulded thermoplastic polyurethane materials. For use with water up to 85°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FKM 90 Black 6019020105-CMP00700'. Black coloured, compression moulded FKM material. Shore hardness 90. Tested in-radius size 1.1mm. For use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Akfix PS253 Pipe Sealant Medium Strength'. Blue coloured pipe sealant. Apply as per manufacturer's TDS 'Rev.01', issue date '23/10/2019'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weld-On 719 PVCu Clear Solvent Cement'. Clear, colourless solvent cement. Apply as per manufacturer's instructions and cure/dry for 24 hours@5°C(±2°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of deck mounted taps for cold or premixed water (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlet hoses have stainless steel strainers and incorporate approved check valve cartridges, however, the complete products have not been fully tested to demonstrate they provide backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted tap assemblies for cold or premixed water with chromium plated brass bodies. Flow is controlled by a solenoid valve activated via an infra-red sensor and the spout outlets have plastic aerators. Supplied with stainless steel braided PEX lined connection hoses. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose and a manual lever for controlling the temperature. Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel for models 236303 & 236404 only or chromium plated brass for all others). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets incorporate stainless steel strainers and the products are supplied with stainless steel braided PEX line connection hoses. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, electronically controlled tap assemblies (chrome plated brass body). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Supplied with a stainless steel braided PEX lined flexible connection hose. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled via a manual operating single lever on body. The inlets hose incorporates stainless steel strainer and an approved check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection). The spout outlet incorporates a plastic aerator and the product is supplied with metal backnuts. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet, electronically controlled tap assemblies (brass body – various finishes). The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Models xxx.yyy.170E/W are supplied with a click clack waste. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 18 of 47
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
