'GIX96W-BR & GIX99.7W-BR'. Cream coloured ceramic bearing rings manufactured by pressing, sintering & re-working. For use with water up to 85°C.
'ET-52184 & ET-52185'. Factory applied, black coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure both undercoat and finishing coat for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
Range of electronic, touch free, wall-mounted taps (chromium plated brass. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, with either bottom entry (A28-06 XXX models) or side entry (A28-06 side). The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar Cold Water Use Only
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted, single outlet (swivel) combination tap assembly (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass body). Incorporating quarter turn ceramic disc headworks, dome type operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator or flow straightener. The products are supplied with metal backnuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 70.0°C
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 170 of 223
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
