Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'Celcon M90DW CF2001 Natural'. Natual (appears white), injection moulded POM material. For use with water up to 85°C.
'FY Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'FR20240910', dated '2024-09-10'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘NATZINC EP9015 SC PART A-BI.5431’ primer for use with ‘HYDRALFUN AC NOIR PAM -CZL8579’ finish/topcoat. Factory applied, black coloured (once mixed and applied), two-part epoxy primer for use with acrylic coating. Mix base & hardener of primer in a 100:10 weight ratio and apply one coat as per manufacturers TDS ‘NATZINC EP9010 BI 5431’, dated ‘February 2024’. No cure required. Apply one coat of the topcoat as per manufacturers TDS ‘HYDRALFUN AC NOIR PAM CZL8579’, dated ‘July 2018’ and cure for 21 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Sigmaguard CSF 585/Blue'. Factory applied, blue coloured, two-component, solvent-free epoxy coating. Mix parts A & B in a volume ratio of 77.5:22.5 and apply as per manufacturer's Product Data Sheet '7785', dated 'August 19, 2022'. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-SRC (U)'. Factory applied, grey coloured Sulphate resistant cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (E)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'JSGL-OPC (U)'. Factory applied, grey coloured Ordinary Portland cement. Mix cement:sand:water in a 1:1.7:0.4 weight ratio and apply as per manufacturer's Work Instructions 'JSGL/WI/14', issue no, '02', revision no. '00', dated '29.09.2018'. Cure for 24 hours@23°C and then 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Hydroplate 1914'. Site applied, two-component, white coloured (once mixed and applied) Epoxy-polyamine coating. Mix parts A & B in a 3:1 weight ratio and apply as per manufacturer's Product Data Sheet 'B034', dated 'September 2024'. Cure coat 1 for 48 hours at 15°C. Cure coat 2 for 21 days at 15°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Grilon TSG-30/4 FA Black 9840'. Black coloured, injection moulded PA material. For use with water up to 85°C.
'Genestar G1350A-M47WF Black'. Black coloured, polyamide 9T material for injection moulding and extrusion purposes. For use with water up to 85°C.
Grilamid LBV-30H FWA natural & black 9225. Grilamid LBV-50H FWA natural & black 9225. Grilamid LBV-65H FWA natural & black 9225. Glass filled (30%, 50% & 65%), injection moulded nylon material available in natural and black colours. For use with water up to 85°C.
'SAFE 10 (H10 + H09, H17 + H04 and N08 + N04)' pipes. Extruded, dual-layered PE pipes comprising of a black coloured inner layer and blue coloured outer layer. Please note that the codes in brackets denote the raw material combinations and only these combinations are approved. In April 2025 ‘H10, H17 & N08’, extruded, single-layered, black coloured PE pipes were added to the approval. Only pipes marked with ‘H10, H17 or N08’ are approved. For use with water up to 40°C.
'BA160E-8229-01'. Black coloured, injection moulded polypropylene material. For use with water up to 85°C.
'WRC EPDM 92645'. Black coloured EPDM liner manufactured by calendaring. Shore hardness 80 A. Tested in-radius size 0.5mm. For use with water up to 23°C.
'ME0940 'O' rings'. Black coloured, injection moulded EPDM rubber 'O' rings. Shore hardness between 40 & 90. Tested in-radii sizes between 1.0mm & 5.0mm. For use with water up to 85°C.
'KF945W, KF955W, KF965W & KF975W'. Black coloured, compression moulded, silicone rubber materials. Shore hardness between 45 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
Range of stop valves with plastic bodies. The valves incorporate a built-in solenoid valve which is operated by a switch located on the valve or by a remote control. The leak detector supplied with models SVSM66MRD & SVSM44MRD is not connected to any water pipe, is independent of the valve and is intended to be installed in the area at risk of leakage. It is intended to detect leakage and sends an electrical signal to close the valve. Please note that claims of leak detection have not been verified by WRAS For use with copper pipe (manufactured to BS EN1057), PEX pipe (manufactured to BS7291-3) and PB pipe (manufactured to BS7291 -2). Maximum working pressure 10.0 bar. Cold water use only.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies. Incorporating a solenoid valve activated via an infra-red sensor. The inlets to the control box incorporate stainless steel strainers and the outlet incorporates a plastic aerator. Maximum working pressure: 8 Bar Maximum operating temperature: 65°C
WC flushing cistern incorporating a side entry BS 1212-4 compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Page 161 of 215
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
