Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member or key and bar operating members (see model). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating bronze bodies and wedges. The valves operate via a non-rising spindle headwork with lock shield or hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85ºC.
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an NBR wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
Double regulating valve with a bronze body, incorporating a DZR brass disc face with PTFE seat. The product incorporates two test points each with an EPDM ‘O’-ring. Maximum working pressure 25.0 bar. Maximum operating temperature 70°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
'M90 POM Particle'. White coloured (opaque), injection moulded POM material. For use with water up to 65°C.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard DT High Build Finish Epoxy Coating'. Factory applied, two-component, grey coloured epoxy coating. Mix and apply as per manufacturer's instructions ‘Document Ref : SPL/R&D/TTD/UI/001, Issue No.01, Version: 01’ dated 01.11.2015. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Intercrete 4841 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '4841/031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SANIBIW WB-R Reinforced Multilayer Hoses' and ‘SANIBIW WB-R Hose’. 'SANIBIW WB-R Reinforced Multilayer Hoses' are dual layered, extruded hoses, consisting of an off-white translucent (natural) silicone rubber inner layer and VMQ silicone rubber (with PES reinforcement) outer layer. The outer layer is available in black, red/brown, white or silver colours. Shore hardness 70. The inner and outer layers each have a tested in-radius size of 1.1mm. ‘SANIBIW WB-R Hose’ is a single layered, translucent (natural), extruded silicone rubber hose with PES reinforcement. Shore hardness 70. Tested in-radius size of 2.0mm. All hoses are for use with water up to 85°C.
'SANIBIW WB Hose’. Single layered, uncoloured & translucent (natural), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size of 2.0mm. For use with water up to 85°C.
Page 158 of 562
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
