'4270' components. Black coloured, injection moulded EPDM rubber components with a shore hardness of 70. ‘O’ rings (in-radius 1.31mm), washers (in-radius 1.05mm) & membranes (in-radius 1.75mm) made in Italy. ‘O’ rings (in-radius 1.31mm) & washers (in-radius 1.05mm) made in China. In May 2024 ‘shaped seals’ (in-radius of 1.8mm) made in Italy, were added to the approval. In November 2024, lip seals (in-radius of 0.7mm) made in Italy, were added to the approval. For use with water up to 85°C.
'Silopren LSR 2630, 2640, 2650, 2660 & 2670'. Natural (appears clear), compression moulded silicone rubber sheet materials. Shore hardness between 30 & 70. Tested in-radius size of 1.0mm. For use with water up to 85°C.
'Innotec Thread Seal'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Würth Adhesivo PVC Tixpro'. Translucent, colourless (un-pigmented) solvent cement. Apply as per manufacturer's instructions. Cure for 24 hours at 23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 75°C.
Range of deck mounted, single hole, single outlet (fixed) electronically operated tap assemblies (Chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The products are supplied with a tee piece for installation prior to the solenoid valve. The inlets of the tee piece incorporate a combined NBR gasket and stainless steel filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The products are also supplied with stainless steel braided PEX lined flexible (connecting) hose assemblies and angled spherical valves incorporating a stainless steel strainer for installation on each inlet. Temperature is controlled by adjusting the opening of each angled spherical valve. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C
A range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a single lever operating member. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of deck mounted sensor taps. The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (models 1070021 and 1070025). Maximum operating temperature 60°C (model 1070024).
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic flow straightener, and the inlet incorporates a plastic filter. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Page 157 of 621
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
