'ITK-STE 221 (cream coloured), ITK-AL 99 (cream coloured) & ITK-AL96 (white coloured)'. Compression moulded and sintered ceramic sealing rings. For use with water up to 85°C.
'Jindal Saw Limited Ordinary Portland Cement - 53 Grade'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a xx ratio of 1:1.5:0.5 and apply as per manufacturer's Work Instructions 'JSAW/AP01/DISP/PRO/WI-09', version '2.0', effective date '01.05.2023'. Cure for 2.5 hours@48°C and then 3 days@30°C. For use with water up to 60°C.
'RAL 5005 Epoxy Coating'. Factory applied, blue coloured Epoxy Coating. Apply as per manufacturer's TDS '31.05.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LM-coat'. Factory applied, blue coloured, two-part Polyurea coating. Mix Part A (KOBECASE PS-6031) with Part B (COBENATE I-362) in a 100:100 volume ratio and apply as per manufacturer's TDS 'Rev. no: 02', dated '16.02.2022'. Cure for 4 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ResiGard APUA (NT) Coating'. Factory applied, grey coloured (once mixed), two-component coating. Mix and apply as per Technical Data Sheet ‘PDS/RG37/Ver15/01/25’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Greentech 5000'. Factory applied, blue coloured Epoxy powder coating. Apply as per manufacturer's 'GRHK/QES GL 2025' and cure for 10 minutes@200°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PolyQuick® P-500 PW'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 05-2025'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SOLID-01'. Factory applied, grey coloured cement mortar. Mix sand, cement and mortar in a weight ratio of 1:1:0.35 and apply as per manufacturer's User Instructions 'SOLID-196', 'Vision: A-2', dated '2019-8-28'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PA6059 Pure Polyester Powder Coating'. Factory applied, blue coloured polyester coating. Apply as per manufacturer's instructions 'file no. FP180515 version 2' dated May 25, 2018. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOD-E-2024/1'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's instructions 'T264', revision '00', dated '16.07.2024'. Cure for 25 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SikaTop®-107 Seal AE'. Site applied, grey coloured, two-part coating. Mix parts A and B in a 1.4 weight ratio and apply as per manufacturer's Method Statement 'V1', dated 'Feb 2025'. Cure Coat 1 for 3 hours at 30°C. Cure Coat 2 for 21 days at 30°C. Between January 2025 and December 2025, the coating is for use with water up to 23°C. Between January 2026 and January 2030, the coating is for use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Evercrete Vetrofluid'. Site applied, colourless, cement waterproofing liquid. Apply two coats as per manufacturer's instructions dated '01 JULY 2024'. Cure Coat 1 for 4hrs 40mins@21ºC and Coat 2 for 36 days@21ºC. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM AC'. Site applied, grey coloured cement mortar. Mix 'NATCEM AC' and water in a weight ratio of 5:1 and apply as per manufacturer's Instructions for Use 'Issue 4', dated '16 September 2024'. Cure for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'UNISILKON TK 002/1000'. Clear lubricant, to be applied as per manufacturer's instructions. For use with water up to 65°C.
'Sinopec Water Pipeline Joint Lubricant (Si) (product code: 509164)'. Clear, translucent silicone base lubricant. Apply as per manufacturer's instructions. No cure required. For use with water up to 23°C.
'MS Schramberg Sintered Barium Ferrite (10-1176001)'. Dark grey coloured Sintered Barium Ferrite ring component. For use with water up to 85°C.
'MS Schramberg Sintered Strontium Ferrite (10-1173001)'. Grey coloured Sintered Strontium Ferrite ring component. For use with water up to 85°C.
'ULTRAMID® T7300EG10 FC Aqua BK23285'. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
'PLUSTEK PAT302PWG50BK10'. Black coloured, injection moulded, glass-fibre reinforced polyamide material. For use with water up to 85°C.
'ULTRAMID B3E2G6 AQUA GREY 7118'. Grey coloured, injection moulded PA6 material. For use with water up to 85°C.
'PB-1 Flexpipe (Grey)'. Grey coloured, extruded polybutylene pipe. For use with water up to 85°C.
'Polimal 122-2 AWTP' (beige coloured) & 'Polimal 1094 AWTP-1' (amber coloured). Contact moulded, unsaturated polyester resin materials. For use with water up to 23°C.
'Ori-Plast Electro-Fusion Fittings'. Black coloured, injection moulded PE 100 Electro-Fusion Fittings. For use with water up to 65°C.
'SCGC HDPE H112PC'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'Shield HDPE-100 Pipe' (extruded) and 'Shield HDPE-100 Fabricated Pipe' (extruded then fabricated). Black coloured, HDPE pipes. For use with water up to 85°C.
'Shield HDPE-100 Moulded Fittings'. Black coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'TEGA PE100-RC Blue fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 85°C.
'Techniplast PE100 Pipes'. Black coloured (with blue stripe), extruded PE100 pipes. For use with water up to 60°C.
'NORYL WM330G-73701 (black), NORYL WM330G 7G8B4911 (grey) & NORYL WM330G-4G8B5291 (beige)'. Injection moulded PPE-PS materials. For use with water up to 85°C.
‘NORYL’ black coloured, grey coloured or beige coloured, injection moulded PPE + PS materials. FE1410PW – 73701. FE1520PW – 73701. FE1630PW – 73701. FE1740PW – 73701. FE1520PW - 4G8B5291. FE1630PW - 4G8B5291. FE1410PW – 7G8B4911. FE1520PW – 7G8B4911. FE1630PW – 7G8B4911. FE1410PW-4G8B5291, FE1740PW-4G8B5291 & FE1740PW-7G8B4911 were added to the approval in April 2025. For use with water up to 85°C
'Agriflow PN16 Compression Fittings'. Black coloured, injection moulded polypropylene fittings. For use with water up to 23°C.
'Hostalen PP H4122 103220'. Polypropylene material for injection moulding and compression moulding. For use with water up to 23°C.
'GW 160m'. White coloured (opaque), thread sealant. For use with water up to 85°C.
'Etinox F-A2002 0715'. Grey coloured U-PVC material for injection moulding and extrusion purposes. For use with water up to 23°C.
'Drincable 800'. Blue coloured, extruded, cylindrical shaped EPDM cable. The EPDM outer sheath is the water contact part and has a shore hardness of 50 and tested in-radius size of between 0.6mm & 1.75mm. For use with water up to 23°C.
'EP60/1 BLK'. Black coloured, compression moulded EPDM diaphragm seal. Shore hardness 60. Tested in-radius size 0.75mm. For use with water up to 85°C.
'B1-4651'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 60. Tested in-radius size 4.6mm. For use with water up to 23°C.
'E7001Z59-10 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 70A. Tested in-radius size 1.85mm. For use with water 85°C.
'EP70 Black EPDM Diaphragm Seals'. Black coloured, compression moulded EPDM diaphragm seals. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Precision782628 EPDM'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E633'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP011470P(KAWN)'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'N146 Sealing Cap and Bellow'. Black coloured, injection moulded nitrile rubber sealing cap & bellow. Shore hardness 70. The cap has a tested in-radius size of 0.6mm and the bellow has a tested in-radius size of 1.0mm. For use with water up to 23°C.
'N8018AA'. Black coloured, compression moulded NBR rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'01/N50 VMQ, 01/N60 VMQ & 01/N70 VMQ White. 01/M50 VMQ, 01/M60 VMQ & 01/M70 VMQ Red. 01/L50 VMQ, 01/L60 VMQ & 01/L70 VMQ Blue'. Range of injection moulded silicone rubber `O` rings and gaskets available in white, red & blue colours. Shore hardness between 50 & 70. Tested in-radii size of between 1.0mm and 2.0mm. For use with water up to 85°C.
'LOCTITE® 6300™’. Green coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet reference ‘0.1’, dated November 2024. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'ULTEM™ PW1010-1000'. Amber coloured, injection moulded PEI (polyetherimide) material. For use with water up to 85°C.
Bidet seat where the flow is controlled via a solenoid valve and discharges via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum operating pressure 10 bar. Maximum operating temperature 40°C.
'51N7511 'O' rings'. Black coloured, injection moulded CIIR 'O' rings. Shore hardness 75A. Tested in-radius size 1.1mm. For use with water up to 85°C.
Material included on initial approval: 'XRRA 410B GR1500'. Material added to approval in December 2025: ‘RRA 406B GR1500’. Grey coloured, injection moulded U-PVC materials. For use with water up to 23°C.
Page 153 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
