'ABS 727-Grey (grey coloured), ABS 727-Dark Grey (dark grey coloured), ABS 727 GR48 (grey coloured), ABS 727 White (white coloured), & ABS 727 Black (black coloured)'. Injection moulded ABS materials. For use with water up to 85°C.
'GIX96W-BR & GIX99.7W-BR'. Cream coloured ceramic bearing rings manufactured by pressing, sintering & re-working. For use with water up to 85°C.
'CER4'. White coloured ceramic disc manufactured by dry-press. For use with water up to 85°C.
'ELM EPX 13'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions to end users reference no. 'ELM/2019/10/001' dated '23/08/2024'. Cure for 10 minutes@130°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 805 B'. Factory applied, blue coloured Acrylic coating. Apply as per manufacturer's TDS 'CR805B/CP826', dated 'Sep 12, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron 451B'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's TDS 'CR451B/CP573X', dated 'Sep 24, 2024'. Cure for 30 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/004', dated '09/06/2025'. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'M-AC010'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user manual 'rev. 2.0R' dated 10/10/2024. Cure for 20 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LH-02 EPDM Hose'. Black coloured, extruded EPDM rubber hose. Shore hardness 80. tested in-radius size 0.8mm. For use with water up to 85°C.
'Berusil CDG 352'. White coloured lubricant. Apply as per manufacturer's instructions. For use with water up to 85°C.
'A7G10E'. Black coloured, injection moulded PPA material. For use with water up to 85°C.
'Grilon AG-30 FWA Black'. Black coloured, injection moulded, PA66-GF30 material. For use with water up to 85°C.
'MLTR PERT-AL-PERT Pipe'. Extruded, multi-layered pipe comprising of a natural (clear) inner layer, aluminium middle layer and white coloured (opaque) outer layer. For use with water up to 85°C.
'FILPEX PE-Xb Pipes'. Extruded, PE-Xb pipes available in brown, blue and white (with blue stripe) colours. For use with water up to 85°C.
'Rifeng PEX/AL/PEX Pipe'. Triple layered, extruded pipe consisting of an off-white coloured PEX inner, aluminium middle layer and white coloured outer layer. For use with water up to 85°C.
'Rifeng PEX Pipe'. Off-white coloured, extruded PEX pipe. For use with water up to 85°C.
'Bingo HDPE Pipes 01'. Black coloured (with blue, external stripes), extruded HDPE pipe. For use with water up to 85°C.
'Bingo HDPE Fittings 02'. Black coloured, injection moulded HDPE fittings. For use with water up to 85°C.
'Hotace HDPE Black Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 80°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
‘+GF+'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'Lubricomp CX94108-GYDKNAT'. Dark grey coloured, injection moulded Polystyrene material. For use with water up to 85°C.
'Lubricomp CG006-NA1G003 Black'. Black coloured, injection moulded polystyrene material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'DL8099F Gaskets and 'O' rings'. Black coloured, compression moulded EPDM gaskets and 'O' rings. Shore hardness 70. Gaskets have an in-radius size of 1.5mm. 'O' rings have an in-radius size of 1.45mm. For use with water up to 85°C.
'EJ820 'O' ring'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.3mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. Between April 2025 and August 2025, the ring was for use with water up to 23°C. Between September 2025 and April 2030, the ring is for use with water up to 85°C.
'R210WM'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'70EP505p'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'70NB502S'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ZL-001 (blue coloured) & ZL-002 (red coloured) O-ring'. Compression moulded silicone rubber 'O' rings. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'WS27TF Pipeseal'. Yellow coloured anaerobic adhesive. Apply as per manufacturer's datasheet issue '1.0'. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions
'Permabond HM135'. Green coloured anaerobic adhesive. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
'ergo 4207 (yellow coloured), 4205 (white coloured) & 4453 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'Vyncolit BXE650W'. Black coloured, injection moulded phenolic material. For use with water up to 85°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass bodies). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of electronic, touch free, wall-mounted taps (chromium plated brass. The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 Bar Maximum operating temperature 65.0°C
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, with either bottom entry (A28-06 XXX models) or side entry (A28-06 side). The inlet incorporates a plastic strainer. Maximum working pressure 10.0 Bar Cold Water Use Only
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates a self-cancelling diverter to shower outlet with Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3) Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Four-hole, single outlet, (fixed) combination tap assembly with brass bodies (various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members and a manual diverter to shower outlet. The product is supplied with stainless-steel braided EPDM lined flexible hose assemblies between the side valves and spout, and also on the diverter outlet at the base of the spout. The product is also supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Stainless steel inter-locked shower hose incorporating an EPDM lining and NBR gaskets. Maximum operating temperature 85°C. Open outlet use only.
Page 139 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
