‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 High chlorinated polyethylene anticorrosive coating'. Factory applied, blue coloured polyethylene coating. Apply as per manufacturer's TDS/IFU number '001', dated '2022.11.30'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'A/W AQUA (A) Epoxy 100'. Site applied, pale straw coloured epoxy/linseed oil waterproof coating. Apply as per manufacturer's Technical Document 'FSQP-707-05' dated '2021.01.04'. Cure for 6 hours under UV light (wavelength 365μm) at a distance of 150mm. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterProtect® 180’. Site applied, grey coloured, two-component epoxy coating consisting of Part A (grey coloured liquid) and Part B (colourless liquid). Mix Part A and Part B in a mass ratio of 87:13 and apply as per manufacturer's TDS 'MBS_CC-UAE/Pr_180/ /03_23'. Cure coat 1 for 36 hours@20°C. Cure coat 2 for 21 days@20°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Maxline 100 Potable Water Coating Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDSMLI100.rv5.04042023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'ULTRADUR B4300 GK24 HR FC AQUA GREY 35413'. Grey coloured, injection moulded PBT material. For use with water up to 85°C.
'Dowlex 2344'. Natural (appears white), compression moulded LLDPE material. From May 2025, the material may also be used for extrusion purposes. For use with water up to 85°C.
'AY-N130X series'. Injection moulded PPE materials. For use with water up to 85°C. • AY-N130X-GY843 – grey coloured (contains 30% maximum glass fibre, 2% maximum white pigment, 0.01% maximum black pigment). • AY-N130X-YW05 – yellow coloured (contains 30% maximum glass fibre, 1.5% white pigment, 0.5% maximum yellow pigment). • AY-N130X-BK001 – black coloured (contains 30% maximum glass fibre, 0.5% maximum black pigment).
'Innopol CS 4-8000 G'. Grey coloured, compression moulded polypropylene material. For use with water up to 60°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'Superfast Steel (SFST)'. Epoxy putty which has a grey coloured outer layer, a black coloured inner layer and is grey coloured once mixed. Mix layers by hand until a homogenous colour is achieved and then apply as per product label. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'4255 Washers', with a tested in-radius size of 1.0mm. '4255 ‘O’ rings', with a tested in-radius size of 1.31mm were added to the approval in September 2023. Black coloured, injection moulded EPDM washers & ‘O’ rings. Shore hardness of 50. For use with water up to 85°C.
'5594610'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
'ROGM 2022 'O' ring'. Black coloured, injection moulded NBR 'O' ring. Shore hardness 70. Tested in-radius size 4.4mm. For use with water up to 23°C.
‘2061 VMQ 60’, red coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 60. ‘2172 VMQ 70’, blue coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 70. O-rings have a tested in-radius of 2.0mm Washers have a tested in-radius of 2.5mm. Lip seals have a tested in-radius of 0.45mm For use with water up to 85°C.
Page 135 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
