Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with a non-rising spindle and a handwheel operating member. The 960985, 960986 & 960987 suffix models have a brass body and brass wedge, the 850066, 850070 & 850071 suffix models have a DZR brass body and a brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, brass wedges and PTFE seals. The valves are operated via a non-rising spindle with a hand wheel operating member. To be used with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of commercial, front loading washing machines with flow controlled by a solenoid valve and discharged via type AB air gap assembly (verified by test, suitable for backflow protection against fluid category 5). The inlets incorporate a stainless-steel strainer. Maximum working pressure 6 Bar Maximum operating temperature 85°C
Range of electrolytic water conditioning units consisting of stainless-steel tube with a copper/zinc alloy sacrificial anode and brass inlet and outlet connections. Compression models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
'DWKRAL ABS BIANCO 4698 AT'. White coloured, injection moulded ABS material. For use with water up to 35°C.
'J6970 (white coloured) & J6990 (cream coloured)'. Compression moulded Aluminium Oxide Ceramic sealing rings. For use with water up to 85°C.
'CD 101 P6'. Grey coloured (opaque), ceramic disc component manufactured by powder pressing, sintering and grinding. For use with water up to 85°C.
'Art-Coat'. Factory applied, colourless (transparent) PTFE based surface treatment coating. Apply as per manufacturer's instructions 'revision 3' dated 16-03-2020. Cure for 45 minutes@55-60°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lak Series 2000 - Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 25-1113: Description RAL5005 Blue Signal R.C. (dark blue coloured). Code 25-1117: Description RAL5015 Blue Sky R.C. (light blue coloured). Code 29-1116: Description RAL9005 Black Jet R.C. (black coloured). Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Series 2000 – Fusion Bonded Epoxy’. Factory applied, epoxy powder coatings available in the following colours: Code 29-0008: Description RAL9005 Black Deep FBE. Code 25-0084: Description RAL5015 Blue Sky. Code 25-1110: Description RAL5005 Blue Signal. Code 23-0004: Description Red Oxide Primer. Code 25-1160: Description SABSF29 NCS Blue Cornf. Apply as per manufacturer's technical information 'Rev.2,1 Q1 - 2021'. Cure for 10 minutes at 180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Plascoat PPA571 Aqua Blue 536'. Factory applied, blue coloured PE coating. Apply by flock spray coating and fluidised bed dipping (and post-cure as necessary) in accordance with TDS dated 23/02/2015. Please refer to ‘guide to typical coating conditions – batch operation'. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPICOAT 1000'. Factory applied, two-component, red coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/006', 'version 01', dated '03.11.2022'.. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DICOAT 60EX'. Factory applied, two-component, blue coloured epoxy coating. Mix base & catalyst in a 3:1 volume ratio and apply as per user instructions 'SPL/R&D/TTD/UI/007', 'version 01', dated '03.11.2022'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Monolevel 844SP'. Site applied, grey coloured, polymer modified cementitious mortar. Mix mortar with water in a weight ratio of 5:0.6. Apply as per manufacturer's instructions 'Bulletin No. ML844SP/031/010' issued July 2020. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Teadit NA1006'. Green coloured NBR/fibre gasket material manufactured by mixing and calendaring. For use with water up to 65°C.
'Profood High Temp 2'. white coloured (translucent) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Everbuild Plumber's P12 Silicone Grease (Barcode: 5055492703842)'. White coloured silicone grease. Apply as per manufacturer’s instructions. For use with water up to 65°C.
'Vesconite (Grey) and Vesconite Hilube (Cream)'. Extruded bearing material. For use with water up to 65°C.
'Grivory HT1V-5 FWA grey L2172.5'. Grey coloured, injection moulded PA6I/6T-GF50 material. For use with water up to 85°C.
Page 117 of 442
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
