TOOLSTATION LTD Approvals


#1906134

Single hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headwork with either a single lever or cross-top operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
1906134
Expiry date:
30/06/2024
Size:
Stainless steel braided EPDM lined flexible hose assemblies with ½" captive nut end connections.
Marking:
ebb & flo (Trademark of Toolstation) on rear of tap body
Installation Requirements:
R001 R006 R010
Model:
69736 Porth Mono Mixwer Kitchen Tap
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1905088

Range of single hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlet hoses incorporate an EPDM washer on the inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
1905088
Expiry date:
31/05/2024
Size:
Stainless steel braided EPDM lined flexible hose assemblies incorporating ½” captive nut connections.
Marking:
ebb & flo (Trademark of Toolstation) on rear of tap body
Installation Requirements:
R001 R006 R010
Model:
14780 CHESIL MONO MIXER KITCHEN TAP & 38515 FILEY MONO MIXER KITCHEN TAP
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1907073

Range of high neck basin pillar taps (chromium plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic flow straightener & the products are supplied with metal back nuts. Maximum working pressure 10.0 bar Maximum operating temperature 70°C.

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
1907073
Expiry date:
31/07/2024
Size:
½” BSP (M)
Marking:
EBB & FLO (TRADEMARK OF TOOLSTATION) ON REAR OF TAP BODY
Installation Requirements:
R001 R006
Model:
31110 CONTRACT LEVER PILLAR TAPS
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2001107

Deck mounted, single hole, single outlet (fixed) pillar taps, incorporating a non-rising spindle headwork with dome type operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
2001107
Expiry date:
31/01/2025
Size:
½” BSP male
Marking:
ebb & flo (Trademark of Toolstation) on rear of tap body.
Installation Requirements:
R001 R006
Model:
52398 CONTRACT PILLAR TAPS
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1906153

Range of pillar taps (chrome plated brass) incorporating a quarter turn ceramic disc headworks with a single lever operating member controlling the flow. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal back nuts. Maximum working pressure 10.0 Bar, Maximum operating temperature 70°C

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
1906153
Expiry date:
30/06/2024
Size:
½” BSP (M) or ¾” BSP (M)
Marking:
ebb & flo on tap base
Installation Requirements:
R001 R005
Model:
52104 Braye Bath & Braye Basin PILLAR TAPS
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1906154

Two-hole, single outlet (fixed) combination tap assembly (chromium plated brass) incorporating a quarter turn ceramic disc headwork with single lever operating members and a manually operated diverter to shower outlet. The spout outlet incorporates a plastic flow straightener. The inlets incorporate a stainless strainer and an approved single check valve cartridge however the complete product has not been fully tested to demonstrate it provides backflow protection. The product is supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0520 Combination Tap Assemblies
Section Subtitle:
Two hole, metal, single outlet, fixed, manually operated diverter to shower outlet.
WRAS Approval Number:
1906154
Expiry date:
30/06/2024
Size:
¾” BSP (M)
Marking:
ebb & flo on tap body
Installation Requirements:
R001 R006 R020
Model:
52515 Thermostatic bath shower mixer COMBINATION TAP ASSEMBLY
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2002804

Self closing basin tap (chromium plated brass) with spring loaded headwork and dome type operating members. The spout outlets incorporate a plastic flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar, Maximum operating temperature 85°C.

Section:
1820 Taps
Section Subtitle:
Self closing, metal.
WRAS Approval Number:
2002804
Expiry date:
28/02/2025
Size:
½” BSP (M)
Marking:
ebb & flo on tap base
Installation Requirements:
R001 R006
Model:
60081 Non Concussive Basin & 35537 Non Concussive COMBINATION TAP ASSEMBLIES
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1907398

Range of spherical servicing valves having nickel plated ( brass bodies and EPDM ‘O’-rings and can be lever type or screwdriver operated. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:
2260 Valves
Section Subtitle:
Spherical, metal.
WRAS Approval Number:
1907398
Expiry date:
31/07/2024
Size:
See model.
Marking:
TS, SIZE, FLOW ARROW, BATCH CODE & V ON BODY EN1254-2 & SIZE ON NUT
Installation Requirements:
R001
Model:
71997: 15mm compression. 37336: 15mm compression. 16091: ISO valve with handle: 15mm compression. 95951: Angle Servicing valve: 15mm compression x ½” captive nut. 30684: Straight Servicing valve: 15mm compression x ½” captive nut.
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1909411

Range of drain valves with brass and DZR brass bodies (natural or chromium plated finish) with EPDM gaskets and ‘o’rings. The valves incorporate a rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C

Section:
1770 Taps
Section Subtitle:
Draining, metal or plastic - For above ground use only.
WRAS Approval Number:
1909411
Expiry date:
30/09/2024
Size:
see model
Marking:
TS, BATCH CODE, V, BS2879-2 & SIZE ON BODY
Installation Requirements:
R001 R511
Model:
96526-15mm natural Model added November 2020 83905
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1912069

Range of in-line servicing valves (brass or nickel-plated brass body and ball) with EPDM gaskets and a screwdriver operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:
2260 Valves
Section Subtitle:
Spherical, metal.
WRAS Approval Number:
1912069
Expiry date:
31/12/2024
Size:
22mm compression inlet/outlet
Marking:
TS, SIZE, FLOW ARROW, BATCH CODE & V ON BODY EN1254-2 & SIZE ON NUT
Installation Requirements:
R001
Model:
Screwdriver operated. 42958 (Nickel plated Brass)
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1912070

Range of wall mounted hose union taps (various body materials) incorporating a non-rising spindle headwork with a butterfly handle operating member. The spout outlets incorporate a hose union connector. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.

Section:
1780 Taps
Section Subtitle:
Hose union, metal. a. All cold water fittings located outside the thermal envelope, or those outside the building should be protected against damage by freezing. b. A servicing valve shall be fitted to the supply pipe to this fitting and shall be located within the thermal envelope of the building. Where in existing house installations a hosepipe is to be used from an existing hose union tap located outside a house and which is not provided with backflow protection, either: a. The existing hose union tap should be provided with a double check valve (Type EC or ED) located inside the building; or b. The tap should be replaced with a hose union tap that incorporates a double check valve (type HUK1); or c. A hose union backflow prevention (Type HA) or a double check valve should be continuously fitted to the outlet of the tap; or d. Is legally installed in any premises.
WRAS Approval Number:
1912070
Expiry date:
31/12/2024
Size:
½” BSP (M)
Marking:
TS, SIZE, BATCH CODE, EN1213 7 V ON BODY
Installation Requirements:
R001 R040
Model:
60635 (natural brass).
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2005045

Range of double check valve assemblies consisting of two spring loaded in-line check valve cartridges housed in a DZR brass body with a drain port between the cartridges. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:
0034 Backflow Prevention Devices
Section Subtitle:
SCHEDULE 2 - Section 6.2 Type ED - Non-verifiable double check valve.
WRAS Approval Number:
2005045
Expiry date:
31/05/2025
Note:
Not for use with water injected with CO2 gas.
Size:
See model.
Marking:
TS, CR FLOW ARROW & SIZE ON BODY SIZE ON END NUT
Installation Requirements:
R001
Model:
86881: 15mm compression inlet/outlet, 61921: 22mm compression inlet/outlet,
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2007077

Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a click type waste. Maximum working pressure 10 bar. Maximum operating temperature 70°C.

Section:
0450 Combination Tap Assemblies
Section Subtitle:
Single hole, metal single outlet, fixed. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of: • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2007077
Expiry date:
31/07/2025
Size:
Stainless steel braided EPDM lined flexible hose assemblies with ½” captive nut end connections.
Marking:
ebb & flo (brand of Toolstation) on tap body.
Installation Requirements:
R001 R006 R010
Model:
20761
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1905402

Range of in-line adjustable (between 2.8 and 3.2 bar) pressure reducing valves with chrome plated DZR brass bodies and NBR ‘O’ rings. The valves incorporate test ports on the outlet side of the valve and a stainless-steel strainer. Maximum supply pressure 16.0 bar. Maximum operating temperature 85°C.

Section:
2200 Valves
Section Subtitle:
Pressure reducing.
WRAS Approval Number:
1905402
Expiry date:
31/05/2024
Size:
15mm & 22mm compression. ½” BSP (F) & ¾” BSP (F).
Marking:
TS, CR & DATE OF MANUFACTURE YYYY/M/D on body
Installation Requirements:
R001 R120
Model:
44160 ADJUSTABLE PRESSURE REDUCING VALVES
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#1905405

Non-verifiable single check valve assemblies with a DZR brass body. Maximum working pressure 10.0 bar. Maximum operating temperature 85ºC.

Section:
0030 Backflow Prevention Devices
Section Subtitle:
SCHEDULE 2 - Section 6.2 Type EB - Non verifiable single check valve.
WRAS Approval Number:
1905405
Expiry date:
31/05/2024
Size:
see model
Marking:
TS, CR, FLOW ARROW & SIZE ON BODY
Installation Requirements:
R001
Model:
82559 – 15mm compression. 44278 – 22mm compression.
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2010403

Single hole, single outlet (swivel) comination tap assembly (chromium plated brass), incorporation a non-rising spindleheadwork with crosstop type operating members. The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2010403
Expiry date:
31/10/2025
Size:
Stainless steel braided EPDM lined hose assembly with ½” BSP captive nut.
Marking:
ebb & flo on tap base
Installation Requirements:
R001 R006 R010
Model:
49944
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2010404

Single hole, single outlet (swivel) comination tap assembly (chromium plated brass). Incorporation a ceramic disc headwork with dome type operating members. The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2010404
Expiry date:
31/10/2025
Size:
Stainless steel braided EPDM lined hose assembly with ½” BSP captive nut.
Marking:
ebb & flo on base of tap
Installation Requirements:
R001 R006 R010
Model:
88081 COLWELL MONO MIXER COMINATION TAP ASSEMBLY
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2001141

Range of deck mounted, single hole, single outlet (fixed) pillar taps, incorporating a non-rising spindle headwork with cross top operating members. The spout outlet incorporates a plastic flow straightener and the product is supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
2001141
Expiry date:
31/01/2025
Size:
½” BSP male
Marking:
ebb & flo on tap body.
Installation Requirements:
R001 R006
Model:
64284 Cross head Kitchen PILLAR TAPS
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2010405

Single hole, single outlet (swivel) comination tap assembly (chromium plated brass), incorporation a ceramic disc headwork with lever type operating members.The spout outlets incorporate a metal strainer and either a plastic aerator or alternative flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2010405
Expiry date:
31/10/2025
Size:
Stainless steel braided EPDM lined hose assembly with ½” BSP captive nut.
Marking:
ebb & flo on base of tap
Installation Requirements:
R001 R006 R010
Model:
26251 Seaton Mono Mixer Kitchen COMINATION TAP ASSEMBLY
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval


#2105807

Range of pillar taps with brass bodies (chrome plated), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic flow straightener or aerator. The product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating pressure 85°C.

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
2105807
Expiry date:
31/05/2026
Size:
See model
Marking:
ebb & flo on body
Installation Requirements:
R001 R005
Model:
½” BSP (M) 26452 ¾” BSP (M) 62548
Factor:
TOOLSTATION LTD
Company Name
TOOLSTATION LTD
Address
EXPRESS PARK BRISTOL ROAD BRIDGEWATER
Postcode
TA6 4RN

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 1 of 3

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.