Range of spherical valves incorporating (brass bodies - various finishes). Maximum working pressure 16.0 bar, 25.0 bar for model 10.61092.015.CP5R-8510 & 10.61092.015.CP12-8510. Maximum operating temperature 85°C.
Range of spherical valves with various operating members, brass bodies, brass balls, EPDM ‘O’-rings and PTFE seats. Maximum working pressure 40.0 bar. Maximum operating temperature 85°C.
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with plastic bodies for below ground use.. The valves are supplied with loose pipe inserts and are for use with polyethylene pipe (manufactured to BS EN 12201). Maximum working pressure 14.0 bar. Cold water use only.
Water chiller and heater units for under counter installation incorporating an approved double check valve at the inlet, to be used in conjunction with an outlet tap arrangement or flow control device, with a range of taps that are supplied with the chillers. Maximum working pressure 10.0 Bar Maximum operating temperature 98.0°C
'Kubota Powder TK1413F (SPD)'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's TDS 'RP23242', dated 'December 26, 2023'. Cure for 6 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III A (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours@45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSGL-BFSC III B (S)'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.7:0.5 weight ratio and apply as per manufacturer's work instructions 'JSGL/WI/14', 'Issue No. 02', 'Revision No. 00', dated '29.09.2018'. Cure for 4 hours at 45°C (R.H. 85%). For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 93 of 134
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
