Range of dual flush WC syphons incorporating polypropylene bodies and stainless-steel C-links. Cold water use only

Section:

1305 Flushing Mechanisms

Section Subtitle:

WC. Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

250702707

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1 ½” BSP (M).

Marking:

Armitage Shanks and FreeFlo on top of flush valve

Installation Requirements:

R001 R556

Expiry date:

31/07/2030

Model:

EEM10073M67 (7.5”), EEM10073L67 (8”), EEM10073O67 (9.5”), EEM10073U67 (11.5”).

Approval Holder:

Ideal Standard (UK) Ltd

Company Name

Ideal Standard (UK) Ltd

Address

Old Road (Lodge 1) Armitage, Rugeley, Staffordshire

Postcode

WS15 4BT

Country

United Kingdom

General Email

tyeomans@idealstandard.co.uk

View All Listings by this Company

Qmpress Instaboil Range of under counter electric instantaneous water heaters with stainless steel tank and heating element. Open outlet use only. Maximum operating temperature 98°C.

Section:

1365 Heaters

Section Subtitle:

Electric instantaneous, open outlet, mains fed.

WRAS Approval Number:

250604718

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (M).

Marking:

QMPRESS logo printed on front panel. logo; Pressure, Capacity, Model No, WRAS and product info on data label.

Installation Requirements:

R001

Expiry date:

30/06/2030

Model:

Qmpress Instaboil 4in1 Boiler Water Heater Tanks.

Approval Holder:

QMPRESS LTD

Company Name

QMPRESS LTD

Address

Qmpress Ltd Cools, Headford, Killarney

Country

Ireland

View All Listings by this Company

Range of heat interface units providing heating and instantaneous hot water. The central heating and hot water is generated via plate heat exchangers. The central heating circuit contains a pressure relief valve (3.0 bar) and an expansion vessel. Max Temperature & Pressure: Primary Circuit: 6.0 bar at 90°C DHW Circuit: 10.0 bar at 55°C Secondary Circuit 6.0 bar at 90°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/4" BSP (F) captive nut connections

Marking:

Baxi on front cover, Baxi, product info on label on front cover

Installation Requirements:

R001

Expiry date:

31/07/2030

Model:

A/7892284 AquaHeat HD/HWI 12/50 with Heat Meter & Mercurius B/7892283 AquaHeat HD/HWI 12/50

Manufacturer:

Baxi Heating UK Limited

Company Name

Baxi Heating UK Limited

Address

Brooks House, Coventry Road, Warwick

Postcode

CV34 3LL

View All Listings by this Company

Range of horizontal multistage pumps with stainless steel bodies, diffuser and impellers and EPDM ‘O’-rings. The products incorporate a graphite-SiC-EPDM shaft seal. The products incorporate a drain plug. Maximum working pressure 8.5 bar. 9Maximum operating temperature 80°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241002724

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain plug must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

CWMA3 & CWMA5 : 1” BSP (F) inlet x 1” BSP (F) outlet. CWMA7 : 1¼” BSP (F) inlet x 1” BSP (F) outlet. CWMA9 : 1½” BSP (F) inlet x 1¼” BSP (F) outlet. CWMA18 : 2” BSP (F) inlet x 1½” BSP (F) outlet.

Marking:

Winflo logo, model code and product technical information on data-plate.

Installation Requirements:

R001 R415

Expiry date:

31/10/2029

Model:

CMWA range model code: CMWAXX-Y(T) CMWA = Pump type. XX = Nominal flow rate m/3 per hour (3, 5, 7, 9 or 18). Y = Number of impellers. T = 3 phase or (blank) = single phase. CMWA3-2, CMWA3-3, CMWA3-4, CMWA3-5, CMWA3-6 & CMWA3-7. CMWA5-2, CMWA5-3, CMWA5-4, CMWA5-5, CMWA5-6 & CMWA5-7. CMWA7-2, CMWA7-3, CMWA7-4, CMWA7-5 & CMWA7-6. CMWA9-2, CMWA9-3, CMWA9-4 & CMWA9-5. CMWA3-2T, CMWA3-3T, CMWA3-4T, CMWA3-5T, CMWA3-6T & CMWA3-7T. CMWA5-2T, CMWA5-3T, CMWA5-4T, CMWA5-5T, CMWA5-6T & CMWA5-7T. CMWA7-2T, CMWA7-3T, CMWA7-4T, CMWA7-5T, CMWA7-6T & CMWA7-7T. CMWA9-2T, CMWA9-3T, CMWA9-4T & CMWA9-5T. CMWA18-2T, CMWA18-3T & CMWA18-4T.

Approval Holder:

Eautechnik GmbH

Company Name

Eautechnik GmbH

Country

Germany

View All Listings by this Company

Range of multistage centrifugal pumps with stainless steel impellers, intermediate chambers, shaft and outer sleeve. The DPV(M/S) models and DPV(S) models can also incorporate an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressures: Existing models: DPV models 10.0 bar, DPVM models with an oval flange or VME models with integral check valve 16.0 bar, All other DPVM models 25.0 bar. DPV(S) models with an oval flange or DPV(S)(E) models with integral check valve 16.0 bar, All other DPV(S) models and DPH(S)I models 25.0 bar. Maximum operating temperatures: DPHM, DPVE and DPVME models with integral check valve 60°C, all other model variants 100°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250302723

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DPHM 2/4/6 B: 1¼” BSP (F) inlet x 1” BSP (F) outlet. DPV(M/S)(F/E/V/T) 2/4/6 B: Oval flange: DN25, DN32. Round flange: DN25, DN32. External threaded: 1½” BSP (M), Victaulic: DN32 and Tri-clamp: DN32. DPV(S) (F/E/V/T) 10 B/15 B/15 C: Oval flange: DN40, DN50. Round flange: DN40, DN50. External threaded: 1½” BSP (M), Victaulic: DN50 and Tri-clamp: DN50. DPV(S)F 25/40/60/85/125 B: Round flange: DN65, DN80, DN100, DN125. DPH(S)I 2/4/6 B: 1¼” BSP or NPT (F). DPH(S)I 10/15 B/C: 2” BSP or NPT (F).

Marking:

DPVF & logo, model name, PN, WRAS and technical information on adhesive label on body.

Installation Requirements:

R001 R415

Expiry date:

31/03/2030

Model:

DPHM x yy B. Where: x = flow rate m³/h (2, 4 or 6). yy = no. of stages ranges 1-6 stages. ------------------------------------- DPV(M/S)(F/E/V/T) x yy B/C Where: V = Vertically oriented (AISI 304) with coupling. VS = Vertically oriented (AISI 316) with coupling. No indication (V/VS only) = oval flange. F (VF/VSF) = round flange. E (VE) = external thread. V (VV/VSV) = Victaulic. T (VT/VST) = Triclamp. x = flow rate m³/h (2, 4, 6, 10, 15). yy = no. of stages DPV(M/S)(F/E/V/T)……2 B 1-30 stages. DPV(M/S)(F/E/V/T)……4/6 B 1-26 stages. DPV(S)(F/E/V/T)……10 B 1-21 stages. DPV(S)(F/E/V/T)……15 B/C 1-17 stages. -------------------------------------- DPV(S) F xx yy B. Where: V = Vertically oriented (AISI 304) with coupling. VS = Vertically oriented (AISI 316) with coupling. F (VF/VSF) = round flange. x = flow rate m³/h (25, 40, 60, 90(model 85) or 125). yy = no. of stages ……25 B 1-12 stages. ……40/60 B 1-10 stages. ……85 B 1-6 stages. ……125 B 1-4 stages. -------------------------------------- DPHI x yy = Vertically oriented (AISI 304). DPHSI x yy = Vertically oriented (AISI 316). Where: I = Inner thread connection. x = flow rate m³/h (2, 4, 6, 10 or 15). yy = no. of stages DPH(S)I 2/4/6 B 1-14 stages. DPH(S)I 10 B/15 B/15 C 1-8 stages.

Approval Holder:

Duijvelaar Pompen B.V.

Company Name

Duijvelaar Pompen B.V.

Address

Kalkovenweg 13 2401 LJ Alpen aan den Rijn

Country

Netherlands

Phone

0031 0172 488388

View All Listings by this Company