'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2209500

Expiry date:

30/09/2027

Approval Holder:

Tecnopol Sistemas S.L.U

Company Name

Tecnopol Sistemas S.L.U

Address

Finlàndia, 33 Les Franqueses del Vallès, 08520 Barcelona

Country

Spain

View All Listings by this Company

`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2110554

Expiry date:

31/10/2026

Approval Holder:

3M United Kingdom Plc.

Company Name

3M United Kingdom Plc.

Address

Cain Road, Bracknell. Berkshire.

Postcode

RG12 8HT

View All Listings by this Company

Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2202530

Expiry date:

28/02/2027

Approval Holder:

Akzo Nobel Powder Coatings GmbH

Company Name

Akzo Nobel Powder Coatings GmbH

Address

Markwiesenstrasse 50, D72770 Reutlingen

Country

Germany

Phone

+49 7121 519 191

General Email

info@resicoat.com

View All Listings by this Company

'Jotapipe AC1003XT'. Factory applied, green coloured fusion bonded epoxy coating. Apply as per manufacturer's TDS dated 8 June 2021. Cure for 5 minutes@235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5030 Coatings, Paints & Linings

Section Subtitle:

Factory applied pipe & fittings coatings.

WRAS Approval Number:

2202545

Expiry date:

28/02/2027

Approval Holder:

Jotun Powder Coatings Saudi Arabia Co. Ltd.

Company Name

Jotun Powder Coatings Saudi Arabia Co. Ltd.

Address

P.O. Box 10830, Dammam 31443

Country

Saudi Arabia

View All Listings by this Company

'Cementitious Coating 851 White'. Site applied, light grey coloured (once mixed), two-component cementitious coating. Mix Part A (white liquid) with Part B (powder) in a weight ratio of 1:4 then apply in accordance with manufacturer's instructions '851 /031/012' dated 'July 2021'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5038 Coatings, Paints & Linings

Section Subtitle:

Site applied concrete coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2109560

Expiry date:

30/09/2026

Approval Holder:

Flexcrete Technologies Ltd.

Company Name

Flexcrete Technologies Ltd.

Address

Tomlinson Road, Leyland, Lancashire

Postcode

PR25 2DY

Phone

0845 2607005

General Email

Info@flexcrete.com

View All Listings by this Company

'Nitocote CM210 '. Site applied, grey coloured, two-component cementitious coating comprising of Nitocote CM210 White (base coat) and Nitocote CM210 grey (top-coat). 'Nitocote CM210 White' (base coat) consists of Part A (white coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 4 hours@20°C. 'Nitocote CM210 grey' (top-coat) consists of Part A (grey coloured powder) and Part B (white coloured liquid) to be mixed in a mass ratio of 100:27.7. Cure for 8 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5042 Coatings, Paints & Linings

Section Subtitle:

Site applied pipe and fittings coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2205501

Expiry date:

31/05/2027

Approval Holder:

Fosroc International

Company Name

Fosroc International

Address

Drayton Manor Business Park, Coleshill Road, Tamworth, Staffs.

Postcode

B78 3XN

View All Listings by this Company

'NO MORE DAMP Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0420'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5046 Coatings, Paints & Linings

Section Subtitle:

Site applied cistern coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2201518

Expiry date:

31/01/2027

Approval Holder:

Wykamol Group Limited

Company Name

Wykamol Group Limited

Address

Unit 3 Boran Court, Network 65 Business Park, Hapton

Postcode

BB11 5TH

Country

Burnley,

View All Listings by this Company

'Hydradry Tanking slurry'. Site applied, grey coloured, cementitious tanking slurry supplied in powder form. Mix powder:water in a mass ratio of 3.85:1 and apply as per manufacturer's datasheet 'issue 5 - MC0320'. Cure for 7 days and 4 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5046 Coatings, Paints & Linings

Section Subtitle:

Site applied cistern coatings. Compliance with BS6920 relates to the conditions of cure specified in the listing. If the cure conditions are varied from those described below then compliance with BS6920 cannot be assummed without further testing. Where catalysts are required, only tested catalysts in the recommended concentrations should be used. Manufacturer's advice must be sought if any non standard mixing or curing conditions are being considered.

WRAS Approval Number:

2201519

Expiry date:

31/01/2027

Approval Holder:

Wykamol Group Limited

Company Name

Wykamol Group Limited

Address

Unit 3 Boran Court, Network 65 Business Park, Hapton

Postcode

BB11 5TH

Country

Burnley,

View All Listings by this Company

'Monomix WS'. Site applied, grey coloured cementitious waterproof mortar. Mix powder and water in a mass ratio of 7.58:1. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.

Section:

5063 Concrete, Cement and Mortar

Section Subtitle:

Repair materials. High humidity of 80% to 95% is required when curing cementitious materials.

WRAS Approval Number:

2103565

Expiry date:

31/03/2026

Approval Holder:

Flexcrete Technologies Ltd.

Company Name

Flexcrete Technologies Ltd.

Address

Tomlinson Road, Leyland, Lancashire

Postcode

PR25 2DY

Phone

0845 2607005

General Email

Info@flexcrete.com

View All Listings by this Company

'AXIL-76/T-MD'. White coloured (translucent), extruded silicone rubber hose. Shore hardness 80. Tested in-radius size between 0.75mm & 2.1mm. For use with water up to 85°C.

Section:

5140 Hoses & Tubing

Expiry date:

31/12/2026

Approval Holder:

POSA S.p.A.

Company Name

POSA S.p.A.

Address

Via S.Francesco d'Assisi 330, 20861 Brugherio (MB)

Country

Italy

View All Listings by this Company

'PlumbSil & PlumbSil HT'. Colourless silicone greases. Apply as per manufacturer's instructions dated 18th Jan 2022. For use with water up to 65°C.

Section:

5160 Lubricants

Expiry date:

31/01/2027

Approval Holder:

E. Martin & Co. Silicones

Company Name

E. Martin & Co. Silicones

Address

77 West Vale, Neston, Cheshire

Postcode

CH64 0SF

View All Listings by this Company

'S350 Silicone Fluid'. Colourless (transparent) silicone lubricant. Apply as per manufacturer's instructions for use 'LDAP-009', issue 1 dated May 2021. For use with water up to 85°C.

Section:

5160 Lubricants

Expiry date:

31/08/2027

Approval Holder:

Superior Seals Ltd.

Company Name

Superior Seals Ltd.

Address

Nimrod Way, Ferndown Industrial Estate, Ferndown, Dorset

Postcode

BH21 7SH

Country

UK

Phone

01202 854 300

General Email

sales@superiorltd.com

View All Listings by this Company

'Turbine Overmould 208399'. Black coloured, injection moulded, strontium ferrite filled nylon 6 component. For use with water up to 70°C.

Section:

5175 Nylon

Section Subtitle:

Components.

WRAS Approval Number:

2110548

Expiry date:

31/10/2026

Approval Holder:

Gems Sensors Inc.

Company Name

Gems Sensors Inc.

Address

1 Cowles Road, Plainville, CT 06062

Country

USA

View All Listings by this Company

'ForTii® WX11-FC BK00001, ForTii® PA Xgea21 BK28048 & PA Xgea21 BK28048'. 'ForTii® WX12-FC BK00001' was added to the approval in August 2023. Black coloured, injection moulded Polyamide materials. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2202506

Expiry date:

28/02/2027

Approval Holder:

Envalior

Company Name

Envalior

Address

Flughafenstrasse 101, 40474 Dusseldorf

Country

Germany

View All Listings by this Company

'Rilsan BZM 30 O TLD A'. Beige coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2103564

Expiry date:

31/03/2026

Approval Holder:

Arkema France

Company Name

Arkema France

Address

CERDATO, Route du Launay, 27470 Serquigny

Country

France

View All Listings by this Company

'Zytel® RSFG30G50L BK595'. Black coloured, injection moulded glass fibre reinforced nylon (polyamide 610) material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2202511

Expiry date:

28/02/2027

Approval Holder:

Celanese Sales Germany GmbH

Company Name

Celanese Sales Germany GmbH

Address

Am Unisys Park 1, 65843 Sulzbach am Taunus

Country

Germany

View All Listings by this Company

'Zytel® FG70G30HSR3 BK309'. Black coloured, injection moulded nylon material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2203506

Expiry date:

31/03/2027

Approval Holder:

Celanese Sales Germany GmbH

Company Name

Celanese Sales Germany GmbH

Address

Am Unisys Park 1, 65843 Sulzbach am Taunus

Country

Germany

View All Listings by this Company

`Grilamid TR 90 LS Natural & Grilamid TR 90 Natural`. Natural (colourless, transparent), injection moulded nylon materials. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2201529

Expiry date:

31/01/2027

Approval Holder:

EMS-CHEMIE AG

Company Name

EMS-CHEMIE AG

Address

Via Innovativa 1, CH-7013 Domat/Ems

Country

Switzerland

Phone

+41 81 632 78 78

General Email

welcome@emsgrivory.com

View All Listings by this Company

'Tecomid NB40 GR30 NL HC QW'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2202518

Expiry date:

28/02/2027

Approval Holder:

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Company Name

Eurotec Muhendislik Plastikleri San. ve Tic. A.S.

Address

Karamehmet Mah. Avrupa Serbest Bolgesi, Avrasya Bulvari No: 8, TR 59930 Ergene

Country

Turkey

View All Listings by this Company

'Omnix DW 4050 BK 001'. Black coloured, injection moulded PA material (manufactured in Oudenaarde, BE and Changshu, China). For use with water up to 85°C.

Section:

5180 Nylon

Section Subtitle:

Material only. Components made from materials listed in this section may be required to be submitted for audit tests.

WRAS Approval Number:

2201530

Expiry date:

31/01/2027

Approval Holder:

Solvay Specialty Polymers USA, LLC

Company Name

Solvay Specialty Polymers USA, LLC

Address

4500 McGinnis Ferry Road Alpharetta GA 30005-3914

Country

USA

Phone

+1 770 772 8200

General Email

SpecialtyPolymers.Americas@solvay.com

View All Listings by this Company