'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Vulkanite Bio`. Red coloured, compressed fibre gasket material. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
‘Fybar PT 60' (light green on one side and beige on the other). Fibre/NBR gasket material manufactured by calendaring. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Ultramid® B3EG7 black 00564' (Black coloured) & 'Ultramid® B3EG7 uncolored' (appears beige). Injection moulded nylon materials. 'Ultramid® B3EG7 uncolored' is for use with water up to 65°C. 'Ultramid® B3EG7 black 00564' is for use with water up to 85°C.
'EcoPaXX® Q-DWX6 BK00002 & EcoPaXX® Q-DWX10 BK00002’ (black coloured). 'EcoPaXX® Q-DWX6 NA99001 & EcoPaXX® Q-DWX10 NA99001’ (natural – appears beige). Injection moulded polyamide materials. For use with water up to 85°C.
'Green Pipes HDPE Pipes'. Black coloured (with blue external stripe), extruded HDPE pipe. For use with water up to 65°C.
'Green Pipes HDPE Fittings'. Black coloured (with blue external stripe), fabricated butt-fusion HDPE fittings. For use with water up to 65°C.
'XD PE Fitting'. Black coloured, injection moulded polyethylene fitting. For use with water up to 60°C.
'iJoint'. Black coloured, injection moulded polypropylene fitting. For use with water up to 60°C.
'Eurocarboran TIPO A Naturale (132.166.120)'. Natural (appears off-white), injection moulded PP material. For use with water up to 85°C.
'EP10/00/2 BLK EPDM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 65. Tested in-radius size 1.5mm. For use with water up to 85°C.
`TL-KN-006`. Black coloured, compression moulded EPDM rubber material. Shore hardness 75. Tested in-radius size 1.1mm. For use with water up to 23°C.
Black coloured, compression moulded EPDM components. For use with water up to 85°C. ‘559843, 55985 & 559865’ ‘O’ rings. Shore hardness between 60 & 80. Tested in-radius sizes between 1.31mm & 3.49mm. ‘55985 Gasket’. Shore hardness 70. Tested in-radius size 1.0mm. ‘559865 gasket’. Shore hardness 80. Tested in-radius size 1.50mm. When processing an application for a Product Approval incorporating these components, these are the only shapes of components that are covered by the scope of the approval’.
'Sunaflex T 8157'. Black coloured, compression moulded EPDM rubber material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EP50, EP55, EP60, EP65, EP70, EP75 & EP80'. Black coloured, transfer moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius size 1.1mm. For use with water up to 85°C.
'006800.3 washer, 006802.6 washer & 006906.4 slab (made using 7741 compound)'. Red coloured, compression moulded VMQ components. Shore hardness 70. The '006800.3 washer’ has a tested in-radius size of 1.16mm. The ‘006802.6 washer’ has a tested in-radius size of 1.15mm. The ‘006906.4 slab' has a tested in-radius size of 1.17mm. For use with water up 85°C.
'TPE-GB6061G (grey coloured) & TPE-GB6061B (blue coloured)'. Injection moulded TPE materials with a shore hardness of 60. TPE-GB6061G has a tested in-radius size of 1.41mm. TPE-GB6061B has a tested in-radius size of 1.38mm. For use with water up to 75°C.
Floor mounted single hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes - see model). The product incorporates a ceramic cartridge headwork with a single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with a shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 79 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
