‘Zip Aquapoint IV’ range of wall mounted directly heated unvented storage vessels (cased and insulated) incorporating an enamel lined cylinder and safety kit. The cylinder is factory fitted with a temperature and pressure relief valve (7.0 bar/90°C) and a drain valve. The product is supplied with an installation kit comprising of an expansion vessel, tundish and an inlet manifold incorporating a 6.0 bar expansion relief valve, an adjustable pressure reducing valve with stainless-steel strainer (adjustable between 2.7 and 3.3 bar, but pre-set at 3.0 bar), and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The compression connections of the installation kit are for use with copper pipe (Manufactured to EN 1057). Maximum working pressure 5.5 bar. Maximum operating temperature 70°C. Cold supply only.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

250502703

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Aquapoint iV models: ½” BSP (M) inlet and outlets. AQ105 and AQ0108 Installation kits: 22mm compression.

Marking:

Zip on front panel. Zip company logo, model, capacity and other technical information on adhesive label on cylinder body casing.

Installation Requirements:

R001 R511

Expiry date:

31/05/2030

Model:

AP430S - 30 Ltr Direct, AP450S - 50 Ltr Direct, AP480S - 80 Ltr Direct, AP4100S - 100 Ltr Direct. All products are supplied with an installation kit, either AQ105 (AP430S and 450S models) or AQ108 (AP480S and AP4100S models).

Product Images

Approval Holder:

Zip Heaters UK Ltd T/A Zip Water UK

Company Name

Zip Heaters UK Ltd T/A Zip Water UK

Address

Trafalgar House, Trafalgar Business Park, Dereham

Postcode

NR19 1JG

Country

United Kingdom

Phone

0345 600 5005

General Email

sebastian.ducker@zipwater.co.uk

View All Listings by this Company

Ranges of sensor operated flow control devices either mains or battery powered, incorporating a normally closed solenoid valve to control the flow and operated via an infra-red sensor. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8 Bar Maximum operating temperature 65°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

10mm Spigot inlet x 1/2" BSP (M) outlet

Marking:

"D" logo & Dolphin on sensor unit.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

DB6220-aaa-bb/DB6225-aaa-bb DB620-aaa-bb /DB625-aaa-bb DB6210-aaa-bb /DB6215-aaa-bb DB6240-aaa-bb /DB6245-aaa-bb DB6250-aaa-bb /DB6255-aaa-bb DB6280-aaa-bb /DB6285-aaa-bb ‘0’ models (DBxx[x]0-xxx-xx) are 9V mains powered. '5' models (DBxx[x]5-xxx-xx) are 9V battery powered. ‘aaa’ denotes the external surface finish. ‘bb’ denotes the external surface colour.

Approval Holder:

Dolphin Solutions Limited

Company Name

Dolphin Solutions Limited

Address

Southpoint Compass Park Bodiam East Sussex

Postcode

TN32 5BS

Country

United Kingdom

View All Listings by this Company

Range of ‘Tcontrols’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

RT – 1.1/4” BSP (M) to 2.1/4” BSP (M) RF – 48 mm OD

Marking:

"Tcontrols" logo, Model, Voltage, Size and other information on cap.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

Model Code: XXYZS Where XX denotes the boss type and can be replaced with any of the following: RT = Thread Type RF = Flange Type Where Y denotes the heating tube material and can be replaced with any of the following: 1 = Copper 2 = AISI 304 / AISI 304L 3 = AISI 321 4 = AISI 316 / AISI 316L 5 = Alloy 800 / Alloy 825 / Alloy 840 6 = Titanium 7 = AISI 309S 8 = AISI 310 Where Z denotes the brazing system and can be replaced with any of the following: A = Tin Alloy B = Silver Alloy C = Itek Brazing Where S denotes the surface enamelling and can be replaced with either of the following: S = Enamelled Blank = Not Enamelled

Approval Holder:

Thermowatt S.p.A.

Company Name

Thermowatt S.p.A.

Address

Via San Giovanni Battista 21 Arcevia

Postcode

60011

Country

Italy

Phone

+39 0731988246

General Email

thermowatt@legalmail.it

View All Listings by this Company

Heat pump kit incorporating flow and temperature sensors with stainless steel and plastic bodies. Maximum working pressure 5.0 Bar. Maximum operating temperature 90.0°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

R3/4" (M) Straight coupler

Marking:

Fujikoki logo, flow arrow and other technical data on body of flow sensor

Installation Requirements:

R001

Expiry date:

31/05/2030

Model:

Q-1SCK

Product Images

Approval Holder:

Mitsubishi Electric Air Conditioning Systems Europe Ltd.

Company Name

Mitsubishi Electric Air Conditioning Systems Europe Ltd.

Address

Nettlehill Road, Houston Industrial Estate, Livingston, Scotland

Postcode

EH54 5EQ

Phone

01506 - 44 55 00

General Email

mark.fletcher@m-ace.mee.com

View All Listings by this Company

Manufacturer:

Fujikoki

Company Name

Fujikoki

Address

1-22-18, Harigaya, Utsunomiya-City, 321-0137, Tochigi Prefecture

Country

Japan

General Email

View All Listings by this Company

Range of ‘SureCal’ immersion heater elements incorporating brass or DZR heads with either a copper, stainless steel, alloy or titanium heating element and a black EPDM ‘O’-ring. Open outlet use only. Maximum operating temperature 99°C

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

RT – 1.1/4” BSP (M) to 2.1/4” BSP (M) RF – 48 mm OD

Marking:

'SureCal' logo, Model, Voltage, Size and other information on label.

Installation Requirements:

R001

Expiry date:

30/09/2029

Model:

Model Code: XXYZS Where XX denotes the boss type and can be replaced with any of the following: RT = Thread Type RF = Flange Type Where Y denotes the heating tube material and can be replaced with any of the following: 1 = Copper 2 = AISI 304 / AISI 304L 3 = AISI 321 4 = AISI 316 / AISI 316L 5 = Alloy 800 / Alloy 825 / Alloy 840 6 = Titanium 7 = AISI 309S 8 = AISI 310 Where Z denotes the brazing system and can be replaced with any of the following: A = Tin Alloy B = Silver Alloy C = Itek Brazing Where S denotes the surface enamelling and can be replaced with either of the following: S = Enamelled Blank = Not Enamelled

Approval Holder:

Thermowatt S.p.A.

Company Name

Thermowatt S.p.A.

Address

Via San Giovanni Battista 21 Arcevia

Postcode

60011

Country

Italy

Phone

+39 0731988246

General Email

thermowatt@legalmail.it

View All Listings by this Company