Directory Search Results

Print List

#240704037

Range of stainless steel braided hoses with EPDM liner and NBR or fibre gaskets. DN13 and DN19 Maximum working pressure 10 bar. Maximum operating temperature 65°C. DN25 Maximum working pressure 10 bar. Cold water use only.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240704037
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
see model
Marking:
APL, Date of manufacture (YYYY) and WRAS stamped on ferrule.
Installation Requirements:
R001
Expiry date:
31/07/2029
Model:
H786 13mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.5m H782 13mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.25m H783 13mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.0m H784 13mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 0.75m H785 13mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 0.5m H980 13mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 1.5m H979 13mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 1.25m H978 13mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 1.0m H977 13mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 0.75m H976 13mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 0.5m H775 19mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.5m H769 19mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.25m H772 19mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 1.0m H773 19mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 0.75m H774 19mm stainless steel braided hose 3/4" F STR x 3/4" F BENT 0.5m H981 19mm stainless steel braided hose 3/4" F BENT x 3/4” F BENT 1.5m H829 19mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 1.25m H830 19mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 1.0m H831 19mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 0.75m H832 19mm stainless steel braided hose 3/4" F BENT x 3/4" F BENT 0.5m H984 25mm stainless steel braided hose 1” F STR x 1” F BENT 1.5m H767 25mm stainless steel braided hose 1” F STR x 1” F BENT 1.25m H833 25mm stainless steel braided hose 1” F STR x 1” F BENT 1.0m H768 25mm stainless steel braided hose 1” F STR x 1” F BENT 0.75m H989 25mm stainless steel braided hose 1” F BENT x 1” F BENT 1.5m H988 25mm stainless steel braided hose 1” F BENT x 1” F BENT 1.25m H987 25mm stainless steel braided hose 1” F BENT x 1” F BENT 1.0m H986 25mm stainless steel braided hose 1” F BENT x 1” F BENT
Product Images

Approval Holder:
Aquamatic Products Limited
Company Name
Aquamatic Products Limited
Address
3A & 3B Dakota Business Park, Dakota Way, Burscough, West Lancashire
Postcode
L40 8AF

View All Listings by this Company
Manufacturer:
Aquamatic Products Limited
Company Name
Aquamatic Products Limited
Address
3A & 3B Dakota Business Park, Dakota Way, Burscough, West Lancashire
Postcode
L40 8AF

View All Listings by this Company

Print This Approval


#2211708

Range of stainless-steel braided EPDM lined flexible hose assemblies with various end connections. SCFA models incorporate a spherical valve. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
2211708
Size:
see model
Marking:
South Coast Sales Logo, WRAS and date of manufacture YYYY on crimp connection.
Installation Requirements:
R001
Expiry date:
30/11/2027
Model:
½“ compression x ½" (F) BSP captive nut: EMBW130, length 30cm EMBW150, length 50cm - DN8 ¾“ compression x ¾" (F) BSP captive nut: EMBW530, length 30cm EMBW550, length 50cm - DN13

Approval Holder:
South Coast Sales
Company Name
South Coast Sales
Address
1 Doughcloyne Industrial Estate, Sarsfield Road, Wilton, Cork.
Postcode
T12 TR62
Country
Ireland
Phone
00353 21 - 43 46 143
General Email
info@southcoastsales.com

View All Listings by this Company

Print This Approval


#2012117

Range of multi-layer shower hoses with a PVC inner hose, supplied with EPDM ‘O’-rings. Maximum operating temperature 60°C.

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
2012117
Note:
Open outlet use only.
Marking:
DTC15, WRAS and date of manufacture (MM/YY) on captive nut.
Installation Requirements:
R001
Expiry date:
31/12/2025
Model:
½” BSP (F) conical or captive nut. D50010024 HOS1.5PVS07 HOS1.5PVS07BB HOS1.5PVS07BK HOS1.5PVS07BN HOS1.5PVS07GM HOSE2.0 HOS1.0PVS07 SHOWER HOSES

Approval Holder:
Methven UK Limited
Company Name
Methven UK Limited
Address
3-3A Stone Cross Court Yew Tree Way Golborne Warrington
Postcode
WA3 3JE
Country
United Kingdom
Phone
0800 195 1602
General Email
raluca.olariu@uk.methven.com

View All Listings by this Company

Print This Approval


#240602065

Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240602065
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
See model
Marking:
Dolphin logo on end connections
Installation Requirements:
R001
Expiry date:
30/06/2029
Model:
Model Code: Dolphin Blue DB30abb.ccc.d.eee a’ indentifies the material type of the metal interlocked hose and threaded end connectors; these codes can be: o DB303bb. for brass material o DB304bb. for stainless steel material  ‘bb’ identifies the type of fitting/threaded connector at either end of the hose ranging from DB30a1. to DB30a11. Can be either one or two digits.  ‘ccc’ identifies the length range of the metal interlocked hose from 500mm ‘DB30abb.050’ to 2000mm ‘DB30abb.200’  ‘d’ identifies the external finish to the metal parts from ‘DB30abb.ccc.1 to DB30ab.ccc.9’: o ‘.1’ denotes brushed/satin polished o ‘.2’ denotes mirror polished o ‘.3’ denotes brushed/satin polished with PVD coating o ‘.4’ denotes mirror polished with PVD coating o ‘.5’ denotes powder coated o ‘.6 - .9’ to denote other material and finish options that may be available in the future  ‘eee’ indicates the colour of PVD or powder coat that has been applied from ‘DB30abb.ccc.d.00’ to ‘DB30abb.ccc.d.999’. Can be either two or three digits.
Product Images

Approval Holder:
Dolphin Solutions Limited
Company Name
Dolphin Solutions Limited
Address
Southpoint Compass Park Bodiam East Sussex
Postcode
TN32 5BS
Country
United Kingdom
General Email
Ralph.Mumford@dolphinsolutions.com

View All Listings by this Company

Print This Approval


#240602069

Range of stainless steel or brass double interlocking, TPS lined flexible hose assemblies (various finishes) incorporating EPDM gaskets. Maximum operating temperature 60°C. Open Outlet Use Only

Section:
1863 Tubes
Section Subtitle:
Elastomeric.
WRAS Approval Number:
240602069
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
See model
Marking:
SHS on end connections.
Installation Requirements:
R001
Expiry date:
30/06/2029
Model:
V165W-XX 1/2" Female Connection D17, V940W-XX 1/2" Female Connection D17, V941W-XX 1/2" Female Connection D17, V942W-XX 1/2" Female Connection D17. FXF2CX Trade Name Explanation: FX = Double interlock hose in brass or stainless steel F = TPS Inner Tube 2: Brass Rubber Holders C: WRAS Approved X: Connection Combinations, where X can be replaced with any of the following: A = ½” BSP (F) x ½” BSP (F) B = ½” BSP (F) x M15x1 F = ½” BSP (F) x 3/8” BSP (M) H = ½” BSP (F) x 3/8” BSP (F) I = M15x1 x M15x1 L = M15x1 x 3/8” BSP (M) M = M15x1 x 3/8” BSP (F) Q = 3/8” BSP (M) x 3/8” BSP (M) R = 3/8” BSP (M) x 3/8” BSP (F) S = 3/8” BSP (F) x 3/8” BSP (F) T = ½” BSP (F) x M12x1 AABBCCCC.DDD Trade Name Explanation: AA: identifies hose raw material and diameter, which can be replaced with any of the following: AC = Brass CW508L 022 External diameter 14 AD = Brass CW508L 026 External diameter 14 AQ = Brass CW508L 022 External diameter 15 AR = Brass CW508L 026 External diameter 15 AV = Brass CW508L 022 External diameter 17 AW = Brass CW508L 026 External diameter 17 AF = INOX AISI 304 External diameter 14 AS = INOX AISI 304 External diameter 15 AX = INOX AISI 304 External diameter 17 AJ = Brass CW 508L 022 External diameter 12 BB: identifies the type of external finish, and can be replaced with any of the following: CR = Chromed CZ = Brushed Chrome GM = Raw Brass NS = Brushed Nickel NZ = Brushed Nickel Phosphor IG = Raw INOX IS = Brushed INOX PO = PVD Gold PA = PVD Gold Brushed PG = PVD Black Metal PB = PVD Black Metal Brushed PH = PVD Champagne Brushed PR = PVD Copper Bronze PE = PVD Copper Bronze Brushed PI = PVD Grey 07 Brushed PK = PVD High Brass PQ = PVD High Brass Brushed PM = PVD Pale Gold Brushed PC = PVD Rose Gold Family Surface finishes: Raw, Chromed, Electropolished, Polished, Various Galvanics Finishing, Various PVD Finishing, Various Paint Finishing. CCCC: identifies the type of fittings, which can be replaced with any of the following: Any combination of (2) alphanumeric characters denoting only external aesthetic fittings dimensions. All of fittings are unwetted. DDD: identifies the length (between 50 and 200cm), and can be replaced with any of the following as examples: 050 = 50cm length, 100 = 100cm length, 150 = 150cm length, 200 = 200cm length.

Approval Holder:
Samuel Heath & Sons Plc
Company Name
Samuel Heath & Sons Plc
Address
100 Leopold Street Birmingham
Postcode
B12 0UJ
Country
United Kingdom
Phone
+44 (0) 1217 662 200
General Email
kay.stead@samuel-heath.com

View All Listings by this Company

Print This Approval


#240704052

Range of stainless-steel expansion joints with flanged or threaded end connections. For maximum working pressure please refer to model. Maximum operating temperature 100°C.

Section:
1870 Tubes
Section Subtitle:
Flexible - Metal.
WRAS Approval Number:
240704052
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
See models
Marking:
Model number
Installation Requirements:
R001
Expiry date:
31/07/2029
Model:
Threaded connections: Maximum working pressure 16.0 bar: JP20BS, JP20HS, JP250BS, JP250HS: ½", ¾”, 1”, 1¼”, 1½”, 2”, 2½” & 3” BSP (M). Flanged connections: Maximum working pressure 16.0 bar: JP251FS & JP251VS:15mm, 20mm, 25mm, 32mm, 40mm, 50mm, 65mm, 80mm & 100mm. Maximum working pressure 14.0 bar. JP251FS & JP251VS:125mm. Maximum working pressure 8.0 bar: JP251FS & JP251VS: 200mm. Maximum working pressure 10.0 bar JP251FS & JP251VS: 150mm.

Approval Holder:
Stourflex Ltd
Company Name
Stourflex Ltd
Address
Junction Road Audnam Stourbridge
Postcode
DY8 4YH
Country
United Kingdom
Phone
+441384 393 329
General Email
james.croydon@stourflex.co.uk

View All Listings by this Company

Print This Approval


#2103041

Ultraflow ranges of Direct, Indirect, Solar Single, Solar Twin, Slim Direct and Slim Indirect stainless steel insulated unvented hot water storage cylinders with external expansion. The DHW circuit consists of a temperature and pressure relief valve set at 7.0 bar and 90°C, an inlet control group consisting of a pressure reducing valve adjustable between 2.7 and 3.3 bar, an expansion relief valve (SRV) set at 6.0 bar, a strainer and a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) also supplied with a tundish. Maximum supply pressure to the inlet control group 10.0 bar. Maximum working pressures - Primary circuit 6.0 bar, Secondary circuit 5.5 bar. Maximum operating temperature 65˚C.

Section:
1890 Unvented Heating Apparatus
WRAS Approval Number:
2103041
Note:
Expansion vessels should be installed in the vertical orientation and located so that the length of the connecting pipework is kept to a minimum.
Size:
22mm compression (Inlet Manifold)
Marking:
Ultraflow on front, technical information on adhesive label on body.
Installation Requirements:
R001 R140 R360
Expiry date:
31/03/2026
Proviso:
All solar models must be installed in accordance with this proviso: WRAS Approval - Solar heating system components. “Compliance with the relevant requirements of the Water Supply (Water Fittings) Regulations 1999 has been assessed for this product only as a component of a heating system. If it is to be installed as part of a system using solar energy or ground- or air- source heat pumps for pre-heating water which is to be used as domestic hot water, the Water Fittings Regulations place a legal duty on the installer and user to ensure that the installation and operation of the complete system prevents contamination of domestic hot water by Legionella bacteria, which can grow in water stored at temperatures between 20°c and 45°c.
Model:
UD90 - ULTRAFLOW 90 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UD120 - ULTRAFLOW 120 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UD150 – ULTRAFLOW 150 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UD170 – ULTRAFLOW 170 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UD200 – ULTRAFLOW 200 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UD250 – ULTRAFLOW 250 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UD300 – ULTRAFLOW 300 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UI90-ULTRAFLOW 90 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI120 - ULTRAFLOW 120 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI150 - ULTRAFLOW 150 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI170 - ULTRAFLOW 170 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI200 - ULTRAFLOW 200 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI250 - ULTRAFLOW 250 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UI300 - ULTRAFLOW 300 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UWD170 -ULTRAFLOW 170 INDIRECT SOLAR SINGLE COIL UNVENTED HOT WATER STORAGE CYLINDER UWD200 -ULTRAFLOW 200 INDIRECT SOLAR SINGLE COIL UNVENTED HOT WATER STORAGE CYLINDER UWD250 -ULTRAFLOW 250 INDIRECT SOLAR SINGLE COIL UNVENTED HOT WATER STORAGE CYLINDER UWD300 -ULTRAFLOW 300 INDIRECT SOLAR SINGLE COIL UNVENTED HOT WATER STORAGE CYLINDER UWI170 ULTRAFLOW 170 INDIRECT SOLAR TWIN COIL UNVENTED HOT WATER STORAGE CYLINDER UWI200 ULTRAFLOW 200 NDIRECT SOLAR TWIN COIL UNVENTED HOT WATER STORAGE CYLINDER UWI250 ULTRAFLOW 250 INDIRECT SOLAR TWIN COIL UNVENTED HOT WATER STORAGE CYLINDER UWI300 ULTRAFLOW 300 INDIRECT SOLAR TWIN COIL UNVENTED HOT WATER STORAGE CYLINDER UDS60-ULTRAFLOW SLIM 60 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UDS90-ULTRAFLOW SLIM 90 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UDS120-ULTRAFLOW SLIM 120 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UDS150D-ULTRAFLOW SLIM 150 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UDS170D-ULTRAFLOW SLIM 170 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UDS200D-ULTRAFLOW SLIM 200 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UIS60-ULTRAFLOW SLIM 60 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UIS90-ULTRAFLOW SLIM 90 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UIS120-ULTRAFLOW SLIM 120 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UIS150-ULTRAFLOW SLIM 150 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UIS170-ULTRAFLOW SLIM 170 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UIS200-ULTRAFLOW SLIM 200 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER

Approval Holder:
L & M (HEATING) SUPPLIES LTD.
Company Name
L & M (HEATING) SUPPLIES LTD.
Address
103 LOCKFIELD AVENUE ENFIELD, ENFIELD, MIDDLESEX
Postcode
EN3 7PY

View All Listings by this Company

Print This Approval


#2201107

Range of Ultraflow Air bubble top indirect and direct single coil unvented storage cylinders. The secondary circuit is factory fitted with a temperature and pressure relief valve set at 10.0 bar@90˚C. A safety kit (manifold) consisting of a single check valve assembly, verified by test (suitable for backflow prevention against fluid category 2), strainer, an expansion relief valve set at 8.0 bar and a pressure reducing valve set at 3.0 bar and a tundish is also provided. Alternative inlet control group and temperature and pressure relief valve added January 2023. Maximum working pressure: Secondary circuit: 7.5 bar. Primary circuit: 6.0 bar.

Non-metallic materials and components comply with BS6920 at 65°C

Section:
1890 Unvented Heating Apparatus
Size:
Secondary circuit: 22mm compression. Primary circuit: 22mm compression. Return circuit: 22mm compression.
Marking:
Ultraflow Air on label on front of body.
Installation Requirements:
R001 R140 R360
Expiry date:
31/01/2027
Model:
UOD120 – ULTRAFLOW AIR 120 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UOD150 – ULTRAFLOW AIR 150 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UOD170 – ULTRAFLOW AIR 170 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UOD200 – ULTRAFLOW AIR 200 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UOD250 – ULTRAFLOWAIR 250 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UOD300 – ULTRAFLOW AIR 300 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI120 – ULTRAFLOW AIR 120 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI150 – ULTRAFLOW AIR 150 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI170 – ULTRAFLOW AIR 170 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI200 – ULTRAFLOW AIR 200 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI250 – ULTRAFLOW AIR 250 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOI300 - ULTRAFLOW AIR 300 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UODS120-ULTRAFLOW AIR SLIM 120 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UODS150-ULTRAFLOW AIR SLIM 150 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UODS170-ULTRAFLOW AIR SLIM 170 DIRECT UNVENTED HOT WATER STORAGE CYLINDER UODS200-ULTRAFLOW AIR SLIM 200 DIRECT UNVENTED HOT WATER STORAGE CYLINDER. UOIS120-ULTRAFLOW AIR SLIM 120 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOIS150-ULTRAFLOW AIR SLIM 150 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOIS170-ULTRAFLOW AIR SLIM 170 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER UOIS200-ULTRAFLOW AIR SLIM 200 INDIRECT UNVENTED HOT WATER STORAGE CYLINDER

Approval Holder:
L & M (HEATING) SUPPLIES LTD.
Company Name
L & M (HEATING) SUPPLIES LTD.
Address
103 LOCKFIELD AVENUE ENFIELD, ENFIELD, MIDDLESEX
Postcode
EN3 7PY

View All Listings by this Company

Print This Approval


#241003001

Exposed wall mounted bar shower mixer (chrome plated brass body), incorporating a two-way ceramic disc diverter headwork controlling the flow with a cubed type operating member. Temperature is controlled independently via a thermostatic cartridge with a cubed type member that incorporates a manual override button. The inlets incorporate flow regulators, plastic strainers and approved single check valve cartridges (however, the complete product has not been fully tested to demonstrate that it provides backflow protection). The product is supplied with a shower handset, shower hose, overhead shower and a riser rail assembly. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
241003001
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Size:
½” x ¾” offset unions.
Marking:
Nabis (brand of Wolseley) on body
Installation Requirements:
R001 R010 R040
Expiry date:
31/10/2029
Model:
D01193

Approval Holder:
Wolseley UK Ltd.
Company Name
Wolseley UK Ltd.
Address
2 Kingmaker Court, Warwick Technology Park, Warwick
Postcode
CV34 6DY
Country
United Kingdom
Phone
01926705792
General Email
martin.lister@wolseley.co.uk

View All Listings by this Company

Print This Approval


#240888001

Range of wall mounted, thermostatic bar shower mixers (brass bodies – various finishes), incorporating a quarter turn ceramic disc headwork that controls the flow with a dome type operating member. Temperature is controlled independently via a thermostatic cartridge with dome type operating member that incorporates a manual override button. Models 801524.001 & 801540.001 incorporate a half turn ceramic disc headwork that diverts the flow to an overhead shower or shower handset. Both inlets incorporate an approved check valve cartridge and stainless steel strainers however, the complete product has not been fully tested to demonstrate it provides backflow protection. Models 801508.001 & 801508.002. Maximum working pressure 10 bar. Maximum operating temperature 65 C. Model 801509.001. Maximum working pressure 10 bar. Maximum operating temperature 60 C. Model 801524.001. Maximum working pressure 5 bar. Maximum operating temperature 60 C. Model 801540.001. Maximum working pressure 5 bar. Maximum operating temperature 65 C.

Section:
2010 Shower Valves
Section Subtitle:
Shower valve(s) with thermostatic temperature control
WRAS Approval Number:
240888001
Basis of Compliance:
Tested to regulators Specification Test Code Sheets
Note:
Models 801524.001 & 801540.001 are supplied with an overhead shower, shower hose & handset. Models 801508.001, 801508.002 & 801509.001 are supplied with a shower hose and handset.
Size:
½”x ¾” BSP (M) offset unions 15mm compression
Marking:
PPI on rear of valves,
Installation Requirements:
R001 R010 R040
Expiry date:
31/08/2029
Model:
801508.001 801508.002 801509.001 801524.001 801540.001

Approval Holder:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company
Manufacturer:
PPI Xiamen Industry Co., Ltd.
Company Name
PPI Xiamen Industry Co., Ltd.
Address
No 88 South Houxiang Road Xinyang Industrial Zone Haicang District Xiamen
Postcode
361022
Country
China
General Email
heatheryang@xmppi.com

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 723 of 1011

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.