AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Sirester EC 0994/AT/V/15'. Pale green coloured orthothalic resin manufactured by hand lay-up. For use with water up to 23°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'HD 8570.29'. Natural (appears white with black specks), high density polyethylene resin material manufactured by rotational moulding. For use with water up to 85°C.
'NORYL™ 731S-701-01-01-00 black coloured, NORYL™ 731S-801-01-01-00 beige coloured, NORYL™ 731S-845-01-01-00 beige coloured & NORYL™ 731S-960-01-01-00 grey coloured'. Injection moulded PPE materials. For use with water up to 85°C
'Durafide® 1130A1T WF900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WF9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EUW-70'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 60°C.
`EP2/9/10 BLK 'O' rings`. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
‘0250-35 (50A), 0260-35 (60A), 0270-44 (70A), 0280-22 (80A) and 0290-11 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘5052911193 (50A), 5062911233 (60A), 5072911255 (70A), 5082911184 (80A) and 5092911126 (90A)’. Black coloured, compression moulded EPDM materials. Shore hardness between 50A & 90A. Tested in-radius size 1.0mm. For use with water up to 23°C.
`WN 22/1/9 BLK` 'O' rings. Black coloured, injection moulded, nitrile rubber 'O' rings. Shore hardness 70. Tested in-radius size 0.89mm. For use with water up to 65°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Flomasta 7619J'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of BS1212-4 diaphragm type inlet valves incorporating a plastic body for use in either side or bottom entry WC cisterns. The valves incorporate an up and over discharge, plastic arm and float. The inlet is fitted with a plastic flow regulator and strainer. Maximum working pressure 10 bar. Cold water use only.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush pneumatic outlet valve. The cistern incorporates an angled servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar. Cold water use only.
Page 8 of 222
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
