Permanent filling/ pressurisation device for primary heating and chilled water closed circuits in domestic and non-domestic premises. The mains and closed circuit system pressures are continuously checked by two pressure sensors and their differential monitored by microprocessors. In the event of a fall in system pressure, and only if the mains pressure is adequate, a solenoid valve operates to allow water into the system. At all other times a second solenoid valve drains the fill chamber to waste, via tundish (meeting the requirements of an air gap to drain), and allowing air to be admitted via an automatic air vent to create an atmospheric disconnection across the transfer chamber. Maximum working pressure 6.0 Bar. Cold water use only.

Section:

1530 Miscellaneous Fittings

WRAS Approval Number:

2203372

Note:

Suitable for backflow protection up to fluid category 3. Consult your water supplier prior to installation

Size:

½” BSP (M)

Marking:

BOSS on front case.

Installation Requirements:

R001

Expiry date:

31/03/2027

Model:

BOSS Direct G4 PERMANENT FILLING/PRESSURISATION DEVICE

Approval Holder:

BSS Industrial

Company Name

BSS Industrial

Address

Travis Perkins PLC Ryehill House Rye Hill Cose Lodge Farm Industrial Estate Northampton

Postcode

NN5 7UA

Country

United Kingdom

Phone

07392109053

General Email

benjamin.cockerill@travisperkins.co.uk

View All Listings by this Company

CR(I)(N)(E) ranges of multistage centrifugal pumps incorporating stainless steel impellers, intermediate chamber and outer sleeve. CR(E) versions have cast iron bases and pump heads coated with black cathodic paint. CRI(E) and CRN(E) versions have stainless steel bases and pumpheads. The pumps are available with the following shaft seals HQQ*, HUU*, HUB*, HQB*, where * can be E for EPDM and V for FKM. Maximum working pressures: CR1, 3 or 5 (2-36 stages) Oval flange: 16.0 bar. CR1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange: 25.0 bar CRI/N1, 3 or 5 (2-36 stages) Flexi clamp with oval flange connection: 16.0 bar CR/I/N1, 3 or 5 (2-36 stages) DIN/ANSI/JIS flange, PJE, Flexi clamp or Triclamp: 25.0 bar CR10 (1-16 stages) Oval flange or DIN/ANSI/JIS flange: 16.0 bar. CR10 (17-22 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI10 (1-16 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI10 (17-22 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar CRN10 (1-22 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR15 or 20 (1-7 stages) Oval flange: 10.0 bar. CR15 or 20 (1-10 stages) DIN/ANSI/JIS flange: 16.0 bar. CR15 or 20 (11-17 stages) DIN/ANSI/JIS flange: 25.0 bar. CRI15 or 20 (1-7 stages) Flexi clamp with oval flange connection: 10.0 bar CRI15 or 20 (1-10 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 16.0 bar. CRI15 or 20 (11-17 stages) PJE, Flexi clamp, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CRN15 or 20 (1-17 stages) PJE, Flexi clamp, Flexi clamp with oval connection, Triclamp or DIN/ANSI/JIS flange: 25.0 bar. CR models: Cold water use only. CRI/CRN models: Cold water use only and from April 2023 99°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

2210906

Size:

Oval flange: Rp 1” - 2”. Flexi Clamp Base: Small Base (CR/I/N1/1(s)/3/5) Ø32, Medium Base (CR/I/N15/20) Ø50. Triclamp Base Small Base (CR/I/N1/1(s)/3/5) DN32, Medium Base (CR/I/N15/20) DN50. Flange Base: Small Base (CR/I/N1/1(s)/3/5) DN25/32, Medium Base (CR/I/N15/20) DN40 and 50. PJE Base: Small Base (CR/I/N1/1(s)/3/5) DN32, Medium Base (CR/I/N15/20) DN50.

Marking:

Grundfos and Grundfos logo, type, Model, Product/Version no., technical info, temperature (WRAS 23C or WRAS 99C), manufacturing country on data plate on motor stool.

Installation Requirements:

R001 R415

Expiry date:

31/10/2027

Model:

CR(I)(N)(E) 1(s) range with 2-36 stages, CR(I)(N)(E) 3 range with 2-36 stages, CR(I)(N)(E) 5 range with 2-36 stages, CR(I)(N)(E) 10 range with 1-22 stages, CR(I)(N)(E) 15 range with 1-17 stages, CR(I)(N)(E) 20 range with 1-17 stages. Model keycode: CR(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE, CRI(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE, CRN(E)(C) 1/1(s)/3/5/10/15/20-A B-C-D-E-XXXE. Where: CR = Pump type and Cast Iron, I = EN 1.4301, N = EN 1.4401, E = Preminum Electronically Controlled Motor, C = Core (Basic) with Electronically Controlled Motor. 1/3/5/10/15/20 = Flow rate [m³/h], (s) = Reduced impeller version. A = No. of stages. B = Code for pump version: A = Basic version, B = Oversize motor, E = Pump with certificate, G = E-pump without operating panel, H = Horizontal version, I = Different pressure rating, J = E-pump with a different maximum speed, L = Pump including Grundfos CUE and certificate, N = With sensor, O = Clean and dryed, P = Undersize motor, R = Belt driven pump, V = Cascade function, X = Special version*, Z = Pump with bearing flange. C = Code for pipe connection: A = Oval flange, CA = Flexi clamp, CX = TriClamp, F = DIN flange, G = ANSI flange, J = JIS flange, N = Changed diameter of ports, P = PJE coupling (Victaulic). D = Code for materials: A = Basic version, C = Carbon-free pump, D = Carbon-graphite filled PTFE (bearings)/tungsten carbide, H = Flanges and base plate EN 1.4408, L = Motor stool, base plate and flanges EN 1.4408, N = Flanges EN 1.4408, R = Silicone carbide /silicone carbide bearing, S = PTFE neck rings, T = Baseplate EN 1.4408, X = Special*. E = Code for rubber parts: E = EPDM, V = Viton. XXX = Code for shaft seal: HQQ, HUU, HUB, HQB. [H = Balanced cartridge seal with O-ring, B = Carbon, synthetic resin-impregnated, U = Cemented tungsten carbide, Q = Silicon carbide]. *Special version ONLY covers the situation where more than 4 options are selected within the same position. This will automatically turn the 4 or more options into an X.

Product Images

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Range of shower handsets and shower heads. The shower handsets have a plastic body (white), NBR ‘O’-rings, and a coloured locking ring around the shower face (see model section). The shower heads have a plastic body (white or chrome plated 02-093173 model), NBR ‘O’-rings, directional adjustment (ball joint) and a coloured interlocking ring either surrounding or central to the shower face (except for the 02-093165 and 02-093173 models which have no ring). The Wall shower T-L models have a combined NBR washer and stainless steel strainer on the inlet.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2209300

Note:

Open outlet used only. Claims made by the manufacturer for antimicrobial properties have not been tested and are not considered part of the approval listing.

Size:

Shower handsets: ½” BSP (M). Shower heads: ½” BSP (F).

Marking:

Shower handsets: T (T Johs. Tandrup A/S logo) on shower handset face. Shower heads: Wall shower T-L models: T (Johs. Tandrup A/S logo) on shower face. Wall shower C-L models: T-safe (brand of Johs. Tandrup A/S) on body. All models, expect for the 02-093173 model, also include a QR code.

Installation Requirements:

R001 R040

Expiry date:

30/09/2027

Proviso:

The product(s) listed on this approval fall under the scope of the GB Biocidal Products Regulations (GB BPR) by either incorporating or producing an active substance and/or incorporating a treated article. The product(s) has/have been judged only against the requirements of The Water Supply (Water Fittings) Regulations 1999 (England and Wales), The Water Supply (Water Fittings) (Scotland) Byelaws 2014 or The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009. The decision of the Scheme to list them is not to be taken as any guide as to their effectiveness to do the job for which the active substance and/or treated article is present. WRAS accepts no liability for the material meeting the requirements of the GB Biocidal Products Regulations.

Model:

Shower handsets: 02-031200 - Shower, S-L (Std. 0,8 Violet), 02-031201 - Shower, S-L (Std. 0,8 Yellow), 02-031202 - Shower, S-L (Std. 0,8 Green), 02-031203 - Shower, S-L (Std. 0,8 Blue), 02-031204 - Shower, S-L (Std. 0,8 light Grey), 02-031190 - Shower T-L (Std. 0,8 A , open Violet lock ring), 02-031191 - Shower T-L (Std. 0,8 A , open yellow lock ring), 02-031192 - Shower T-L (Std. 0,8 A , open Green lock ring), 02-031193 - Shower T-L (Std. 0,8 A , open Blue lock ring), 02-031194 - Shower T-L (Std. 0,8 A , open Grey lock ring). Shower heads: 02-091120 - Wall shower T-L (w. Green Notch), 02-091125 - Wall shower T-L (w. Yellow Notch), 02-091127 - Wall shower T-L (w. Blue Notch), 02-091128 - Wall shower T-L (w. Violet Notch), 02-091129 - Wall shower T-L (w. Grey Notch), 02-093165 - Wall shower C-L (std 1,2 Alpin/Hvid), 02-093167 - Wall shower C-L (std 1,2 Alpin/Violet), 02-093168 - Wall shower C-L (std 1,2 Alpin/Yellow), 02-093171 - Wall shower C-L (std 1,2 Alpin/Green), 02-093172 - Wall shower C-L (std 1,2 Alpin/Blue), 02-093173 - Wall shower C-L (std 1,2 Chrome/Grey 7047).

Product Images

Approval Holder:

T-safe A/S

Company Name

T-safe A/S

Address

Gydevang 1, Alleroed

Postcode

3450

Country

Denmark

Phone

+45 61610518

General Email

moj@t-safe.com

View All Listings by this Company

Manufacturer:

T-safe A/S

Company Name

T-safe A/S

Address

Gydevang 1, Alleroed

Postcode

3450

Country

Denmark

Phone

+45 61610518

General Email

moj@t-safe.com

View All Listings by this Company

Range of shower columns with an integral brass body and an aluminium painted column with chrome plated upper. Flow is controlled by a solenoid valve activated by an infrared sensor. The shower head inlet incorporates a combined NBR washer and stainless steel filter. The shower outlet incorporates a plastic flow regulator. The product is supplied with an inline ½” BSP (M) x ¾” BSP (F) screwdriver operated spherical valve with chromium plated brass bodies and ball for installation on the inlet. The product drains down after each use via an integral LLDPE tube leading to a drain outlet at the base of the column. Maximum working pressure 8.0 bar. Cold water use only.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2204349

Size:

½” BSP (M) (to spherical valve).

Marking:

Presto on front panel.

Installation Requirements:

R001 R040 R260

Expiry date:

30/04/2027

Model:

27477 - DL400 SE LYNX 30” 8L/MN pile RA droit complet (battery). 27479 - DL400 SE LYNX 30” 8L/mn SECT220/7V RA DROIT CPLT (mains).

Approval Holder:

Les Robinets Presto S.A

Company Name

Les Robinets Presto S.A

Address

4 Rue Lavoiser St. Georges De Didonne

Postcode

17110

Country

France

Phone

+33 546 053 452

General Email

l.granseigne@presto.fr

View All Listings by this Company

Manufacturer:

Les Robinets Presto S.A

Company Name

Les Robinets Presto S.A

Address

4 Rue Lavoiser St. Georges De Didonne

Postcode

17110

Country

France

Phone

+33 546 053 452

General Email

l.granseigne@presto.fr

View All Listings by this Company

Range of drain taps incorporating brass bodies, EPDM seats and washers and a non-rising spindle headwork. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1770 Taps

Section Subtitle:

Draining, for above ground use only.

WRAS Approval Number:

2112066

Size:

See Model

Marking:

B&Q (brand of Kingfisher), size and PN10 on body

Installation Requirements:

R001 R511

Expiry date:

31/12/2026

Model:

EPH_VAL20_0049a Drain-Off Cock - (15mm Capillary), EPH_VAL20_0052a Drain-Off Cock - (1/2” BSP (M)),

Approval Holder:

Kingfisher International Products Ltd.

Company Name

Kingfisher International Products Ltd.

Address

1 Paddington Square, London

Postcode

W2 1GG

Phone

07721 260713

General Email

eric.capotummino@kingfisher.com

View All Listings by this Company