'LATENE AG7H G/30 BLACK F:3352'. Black coloured, injection moulded PP material. For use with water up to 23°C.
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
'RBL-9200-20, RBL-9200-30, RBL-9200-40, RBL-9200-50, RBL-9200-60, RBL-9200-65 & RBL-9200-70'. Transparent, colourless injection moulded silicone rubber materials. Shore hardness between 20 & 70. Tested in-radii size between 0.75mm & 2.89mm. For use with water up to 85°C.
‘Wall mounted, electronically operated tap assemblies (brass bodies - in various finishes). The flow is controlled by a solenoid valve that is actuated via an infra-red sensor on the spout. The spout outlet incorporates plastic aerators. Maximum working pressure 6 bar. Maximum operating temperature 65°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled by a solenoid valve that is activated via an infrared sensor. The spout outlet incorporates an aerator. Maximum working pressure: 8.0 Bar. Maximum operating temperature 65°C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Thermostatic cartridge incorporating a plastic body and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet. Supplied with click waste outlet – verified by test. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of Single hole, single outlet fixed combination tap assemblies incorporating ceramic disc cartridge headworks with single lever operating members. Models XB-MP-028, XB-MP-030, XB-MP-050, XB-MP-051, and XB-MP-052 incorporate plastic aerators, Models XB-MP-027, XB-MP-029, XB-MP-031 and XB-MP-032 incorporate a plastic flow straightener. Maximum working pressure all models 10.0 bar. Maximum operating temperature 85⁰C for Models XB-MP-018 and XB-MP-035 all other models are 65⁰C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Single hole, single outlet (fixed) combination tap assembly with brass bodies (various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a pop-up waste. Maximum working pressure: 10Bar. Maximum operating temperature: 60°C.
Floor mounted single hole, single outlet (fixed) combination tap assembly (brass bodies -various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 66 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
