Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
'KOCETAL K300, K500 & K700'. Off-white coloured (opaque), injection moulded acetal materials. For use with water up to 85°C.
'Magnum 8391 UV White TM8302386'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'BPL High Build QD Bitu Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer’s data sheet ‘427-rev03’ dated 'Feb' 2024'. Cure: flash off for 15 minutes at ambient temperature of 30°C, followed by stoving at 55°C for 10 minutes and then 7 days maturation at ambient temperature of 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS EPX-02 Solvent Free Epoxy Coating and Hardener'. Factory applied, blue coloured (once applied), epoxy coating for use with Polyamine hardener. Mix coating & hardener in a 3.5:1 volume ratio and apply as per manufacturer's painting instructions 'Document Code 30', 'Rev No 7', dated '01.09.2018'. Cure for 7 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Witcoat SF Epoxy Red Primer. Factory applied, red coloured, two-component epoxy primer. Mix parts A & B in a 3:1 volume ratio and apply as per manufacturer's data sheet '15.09.2023 Rev No.: 00'. Cure for 7 days@30°C. For use with water up to 50°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix & cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's TDS 'ECL/ TDS / ES1212', issue date '2-Feb-14', version '0'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Unitec 300 Green'. Green coloured compressed fibre gasket material manufactured by calendaring. For use with water up to 23°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
Klingersil C-4430 plus. NBR fibre gasket material, manufactured by calendaring, which is red on one side and beige on the other side. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Novus N34 & SF3300'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, maufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'VESTAMID L1930 Material (Natural)'. Natural (appears beige in colour), injection moulded polyamide 12 material. For use with water up to 85°C.
'Paryls PPA A6200GLXX' (XX denotes the weight percentage of glass fibre between 30% to 50%). Black coloured, glass fibre reinforced polyamide materials manufactured by twin screw extrusion. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ketaspire KT-820 GF30 BG20'. Brown coloured, injection moulded PEEK material. For use with water up to 85°C.
'Veradel AG-330 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'Ultrason® P 3010 Blau 80100'. Blue coloured, injection moulded PPSU material. For use with water up to 85°C.
Page 65 of 113
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
