'JIZJ-1'. Factory applied, light grey coloured Portland cement mortar. Mix cement, sand and water in a ratio of 1:1.7:0.55. Cure for 5 hours and 30 minutes@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'KOPATCH PC300-D/BLUE'. Factory applied, two component, dark blue coloured epoxy resin coating. Mix parts A & B in a volume ratio of 2:1. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925P Light Grey'. Site applied applied, two-component, grey coloured (once mixed) epoxy coating comprising of Part A (grey coloured, opaque paint) and Part B (brown coloured, translucent liquid). Mix Parts A and B in a 4.93:1 mass ratio. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 925 White with Ceilcote 680M Primer'. Site applied, white coloured (once mixed), two-component epoxy coating comprising of a two-component primer and two-component top-coat. The primer (Ceilcote 680M) comprises of Part A (uncoloured liquid) and Part B (uncoloured liquid). Mix Parts A and B in a 3:1 volume ratio. Cure for 10 days@30°C. The top-coat (Interline 925 White) comprises of Part A (white coloured, opaque paint) and Part B (white coloured, opaque paste). Mix Parts A and B in a 4.99:1 mass ratio. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novus 30'. Orange coloured, nitrile rubber/aramid fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Ferolite NAM 30'. Green coloured fibre/NBR gasket material manufactured by calendaring. Shore hardness 42A. For use with water up to 65°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Aldex C800 Na (16-50 US mesh resin), Aldex C800x10 Na (16-50 US mesh resin), Aldex C800F (Na) (30-70 US mesh resin) & Aldex C800F (K) (30-70 US mesh resin)'. Ion exchange resins which are black coloured except C800F (Na) which is brown coloured. For use with water up to 23°C.
'TECHNYL ® SAFE A 219WFC V30 BK’ (black coloured) & ‘TECHNYL ® SAFE A 219WFC V30 NC’ (natural, appears off-white). Injection moulded, glass fibre reinforced polyamide 6.6 materials. For use with water up to 85°C.
'RADILON® DT RV300RKC2 106 NT to RADILON® DT RV500RKC2 106 NT and RADILON® DT RV300RKC2 306 BK to RADILON® DT RV500RKC2 306 BK'. Natural (appears off-white in colour) or black, injection moulded glass fibre filled PA6.12 materials. For use with water up to 85°C.
‘TECHNYL ® SAFE D 219WFC V30 BK’ & ‘TECHNYL ® SAFE D 219WFC V50 BK’. Black coloured, injection moulded, glass fibre reinforced polyamide 6.10 materials. For use with water up to 85°C.
'RILSAN® BUM 30 O'. Grey coloured, injection moulded PA material. For use with water up to 23°C.
‘Tecomid NA40 GR30 BK005 HS QW, Tecomid NA40 GR35 BK005 HS QW, Tecomid NA40 GR40 BK005 HS QW, Tecomid NA40 GR45 BK005 HS QW & Tecomid NA40 GR50 BK005 HS QW’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Badadur PBT9 GF30 graphit 371 (grey coloured) & Badadur PBT9 GF30 Alpinweiss 230c (white coloured). Injection moulded Polybutylene terephthalate (30% glass fibres) materials. For use with water up to 65°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
'Moplen EP 300 K PP Cover'. White coloured, translucent, injection moulded polypropylene cover. For use with water up to 85°C.
‘ELASTOSIL® R plus 4303/60 mH (60), ELASTOSIL® R plus 4303/70 mH (70) and ELASTOSIL® R plus 4303/80 mH (80)’. Extruded, natural (appears white in colour) platinum cured HTV silicone rubber with a shore hardness of between 60 & 80. Tested in-radius size 2.0mm. The rubbers may also be coloured using the following ELASTOSIL® Color Pastes PT in a maximum of 1% content: PT Carbon black RAL 9005. PT Red brown RAL 3013. PT Red RAL 3000 F. PT Yellow RAL1016 PT Yellow RAL 1026 F PT Yellow RAL 1021. PT Grey RAL 7040. PT Dark blue 5010. PT Ultramarine blue RAL 5002. PT Violet RAL 4001. PT Green RAL 6017. PT Black RAL 9017. PT White RAL 9010. PT Yellow RAL 1033. PT Orange RAL 2004 F. PT Violet RAL 4002. PT Blue RAL 5022. PT Helio green RAL 6004. For use with water up to 85°C.
'Griffon WDF-05'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6311380 20200708'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of side entry BS1212-4 (2016) delayed action or non-delayed action type float operated valves for WC flushing cisterns. The inlet incorporates an optional flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Bottom entry BS1212-4 (2016) compact type float operated valves for WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Page 7 of 108
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
